Parts for Ge GFWS2605F0RR: Cabinet (2) Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

A replacement pressure sensor that monitors air/differential pressure and sends a signal to the appliance control so the unit can respond correctly. Helps restore accurate pressure readings and resolve pressure-related faults and errors. What it does

• Detects air/differential pressure changes and reports them to the control board for proper system sequencing.
• Helps the control identify pressure faults and can affect diagnostic error codes or sensor-failure indications.
• A failed sensor may cause intermittent operation, incorrect diagnostics, or system faults tied to pressure monitoring.
• Works as the direct replacement sensor component—matches the OEM function when replacing a defective unit.

• One pressure sensor

• Disconnect power to the appliance before starting work to avoid shock or damage.
• If the sensor is in a water-connected circuit, shut off the water supply before removal.
• Handle the sensor and its electrical connector carefully; avoid contamination of sensing ports.
• Verify the part number and orientation before final installation and test the appliance after reassembly.

This molded wire tie standoff provides a secure anchor point for a cable tie to hold wiring and harnesses away from moving parts and hot or sharp surfaces, helping reduce wear and electrical risk. Fits common HVAC and appliance wiring panels. What it does:

• Anchors wire ties to the appliance cabinet or chassis so harnesses stay routed and secured
• Prevents wires from rubbing on sharp edges, hot components or moving parts
• Helps stop intermittent electrical issues from loose or vibrating connections
• Reduces noise from loose wiring that can vibrate during operation

• One wire tie standoff

• Disconnect power before servicing the appliance to avoid shock or damage
• Mount in the original standoff hole or approved panel location; secure a cable tie through the top loop to hold the harness
• Use the correct fastener or snap method for your model—do not force or overtighten
• If routing or attaching multiple wires, verify clearance from heating elements and moving parts

This clamp secures a flexible hose or line to a fitting, helping prevent leaks and keep connections stable during normal appliance operation. A small but essential fastening part for fluid or air lines. What it does:

• Holds a hose or line firmly to a barb, spud, or pipe to maintain a sealed connection
• Helps prevent leaks caused by loose or slipping hoses
• Keeps plumbing or venting lines routed and secure under vibration
• Common replacement when clamps become corroded, cracked, or lose tension

• Inspect mating hose and fitting for damage before installing a new clamp
• Tighten securely but avoid over-tightening, which can cut or deform the hose
• Use appropriate tools (screwdriver or nut driver) and follow appliance safety procedures
• Disconnect power and water supply when working on electrical or plumbing connections

The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.

Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.

Symptoms of a bad Dryer Wire Tie include:

• Loose or unsecured internal wiring
• Interference with dryer components during operation
• Electrical malfunctions or short circuits
• Wires appearing frayed or damaged due to improper support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This OEM replacement part is the main control board for washers. The main control board is the part that controls the functions of the dryer. It is the main component that sends signals to the washer to perform its intended functions, controlling the desired washer settings. If the washer is no longer turning on, spinning properly, or effectively washing, it might be time to replace the main control board. While it might seem difficult to replace this part, it's actually a simple process. First, pull the washer forward to access the back panel. Remove the upper back panel. Push the front of the control panel and pry it up with a putty knife removing it from the mounting brackets. Disconnect any wires attached to the old control board, and be sure to take note of which wires go where by taking a photo with a phone camera. Remove the mounting screws from the control board. Release the locking tabs and pull the control board out of the console. Position the new board in place and pop it into the locking tabs. Reconnect the wires into the back of the new control board. This genuine control board is sold individually is compatible with GE, Hotpoint, RCA, and Sears/Kenmore brand washers.

The Harness Pigtail is an OEM part for GE washing machines. As the electrical conduit linking components, pigtails funnel power and communication signals between control boards, motors, and other systems. Proper connections are key for machines to function properly.  

Symptoms of a bad harness pigtail include:

• Intermittent glitches where programs reset or machines fail to start
• Communication errors between boards 
• Power disruptions leading to improperly heated or spun cycles  

Causes are generally related to wear from continuous flexing/bending as machines operate as well as potential damage or shorting from water damage over time.

This genuine GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. Installing an OEM harness pigtail ensures all systems maintain solid electrical teamwork for thorough, consistent washing.

This silicon controlled rectifier (SCR) switches and regulates power in compatible appliance control circuits, helping the unit deliver correct power to heating elements or motors. It's a direct replacement component when the original SCR fails. What it does

• Acts as a solid-state switch that controls current flow to heating elements, motors or other high-current circuits.
• Fails open or shorted when worn; common symptom is loss of heating, intermittent power to the controlled component, or no operation on affected circuits.
• Provides fast, repeatable switching compared with electromechanical relays.
• Designed for stud-mount installation with insulated/marked terminals for correct wiring.

• One silicon controlled rectifier (SCR) as listed.

• Disconnect all power before accessing or replacing the SCR to avoid shock or equipment damage.
• Note terminal orientation and wiring before removal; replace with the same terminal/stud configuration.
• Avoid electrostatic discharge to the replacement part; handle by the body and avoid touching terminals.

This long shipping bolt secures the washer's tub and suspension for transport, protecting internal components during delivery or relocation. Replace missing or damaged shipping hardware to safely immobilize the drum before moving the appliance.

• Threads into the designated transport points to lock the tub/suspension for moving
• Limits internal movement to help prevent damage to shocks, bearings, and hoses in transit
• Intended for preparing the washer for shipment or relocation; remove before use
• Use when the original long shipping bolt is missing, stripped, or damaged

• Unplug the washer and shut off water before installing or removing shipping bolts
• Refer to your model documentation for correct bolt locations and required quantity; some models use multiple bolts and different lengths
• Insert through the rear cabinet transport holes and tighten until snug; do not overtighten
• Remove all shipping bolts and save them for future moves before operating the washer

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

A short shipping bolt that secures internal components during transport to prevent movement and damage. Use this bolt when preparing or returning a refrigerator or freezer for shipment. What it does:

• Locks internal assemblies in place during delivery or relocation to reduce shifting and damage
• Helps stabilize compressor/bracket or cabinet components while the appliance is moved
• Commonly fitted before transport and removed before normal operation to avoid stress on components
• Replaces a lost or damaged short shipping bolt to restore proper transport protection

• One short shipping bolt assembly

• Install or remove with the appropriate wrench or socket; avoid overtightening
• Remove all shipping bolts before powering on the appliance and restore any caps or plugs
• Follow the appliance owner manual for exact bolt locations and transport procedures

Size: 8 - 18 ab.

This shipping bracket is a transport stabilizer that secures internal components during delivery and handling to prevent movement and damage. It removes after installation so the appliance can operate normally. What it does:

• Holds internal parts steady during shipment to protect fragile components
• Prevents movement-related damage while the appliance is transported
• If left installed, may cause vibration, noise, or prevent proper operation
• Used by technicians and installers when preparing or unpacking appliances

• Unplug the appliance and follow manufacturer's unpacking instructions before removing or installing
• Remove only the fasteners explicitly securing the bracket; keep hardware for reinstallation if needed
• Keep the bracket and hardware for future transport; do not leave bracket installed during normal operation

Includes 12 screws.

A replacement plastic wire tie used to secure wiring harnesses and small tubing inside appliances, keeping wires organized and away from moving parts or hot surfaces for safer operation and reduced noise. What it does:

• Holds wiring and small hoses in place to prevent rubbing, chafing, or contact with moving components
• Helps stop wire harnesses from vibrating or rattling during operation
• Reduces risk of electrical shorts caused by loose or misplaced wires
• Keeps wiring routed neatly for easier servicing and inspection

• Disconnect power to the appliance before servicing
• Position wires, loop the tie around them, tighten to secure, and trim excess tail
• Do not overtighten; avoid cutting into insulation
• Keep wire routing clear of sharp edges, high-heat areas, and moving parts

This 4-foot rubber inlet hose set supplies water to your appliance and replaces worn or leaking lines to restore proper water flow. Durable rubber construction resists kinks and flexing for reliable service. What it does:

• Connects the household water supply to the appliance so dispensers, ice makers or valves receive water
• Replaces cracked, split or leaking inlet hoses that cause visible leaks or water under the appliance
• Helps restore normal water flow when restricted or deteriorated tubing reduces supply
• Flexible rubber design allows easier routing behind appliances

• Turn off the water supply and unplug the appliance before installing
• Hand-start fittings to avoid cross-threading; tighten per the appliance/manual recommendations
• Inspect new hoses for damage before installation and check for leaks after restoring water

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.