Parts for Hot Point HPS10LGVBRBB: Cabinet Parts

This is a replacement evaporator cover screw that secures the evaporator cover/trim in the refrigerator evaporator compartment, restoring proper panel fit and helping maintain airflow and temperature control. What it does:

• Fastens the evaporator cover or trim to the evaporator housing or cabinet
• Keeps the evaporator cover secure to prevent rattling and air leaks
• Helps maintain correct airflow over the evaporator for consistent cooling
• Small hardware solution for loose or missing evaporator cover mounting points

• One evaporator cover screw (quantity: 1)

• Intended for use where the evaporator cover screw is missing, stripped, or damaged
• Use matching screwdriver/drill bit and avoid over-tightening to prevent stripping the hole or cracking plastic trim
• Disconnect power to the appliance before accessing internal components and work with caution around sharp sheet metal and cold evaporator surfaces

This air duct cover directs cold air through the refrigerator compartment and helps keep airflow even for consistent cooling. It replaces a cracked, broken or missing duct housing to restore proper air circulation. What it does

• Guides cold air from the evaporator into the fresh-food compartment to help maintain temperature balance
• Helps prevent frost and cold-air leakage caused by damaged or loose ducting
• Can reduce uneven cooling or warm spots when the original cover is damaged
• Fits where the air path is sealed or routed through the freezer/refrigerator cavity

• One air duct cover

• Disconnect power to the appliance before beginning any work
• Access typically requires removing interior shelves, drawers or a rear freezer panel; keep fasteners for reassembly
• Handle plastic parts carefully to avoid cracking; align tabs/clips before fastening
• Restore power and verify normal airflow and temperatures after installation

This cold control housing duct directs cold-air flow around the refrigerator's cold control assembly to help maintain consistent temperature control. It replaces cracked or damaged housings that can allow air leaks or improper airflow. What it does:

• Channels cold air around the thermostat/cold control for reliable temperature sensing
• Protects the control assembly from direct airflow and debris that can affect operation
• Helps prevent air leaks that lead to uneven cooling or excessive run time

• Intended to be installed by someone familiar with appliance disassembly; follow manufacturer instructions
• Disconnect power to the appliance before beginning any repair to avoid shock
• Handle gently to avoid breaking plastic tabs; confirm proper fit before reassembling panels
• No special tools required beyond common hand tools; your model diagram for removal steps

The Cold Control Thermostat is an OEM component specifically designed for GE refrigerators. It plays a critical role in regulating the refrigerator's temperature. 

The thermostat monitors temperature levels inside the fridge and appropriately triggers the compressor and cooling system to maintain consistent cold temperatures for food storage. Precise thermostat operation is crucial for optimal preservation of perishable goods.

Symptoms of a bad thermostat include:

• Fluctuating temperatures where the fridge is too warm or too cold 
• The compressor and cooling system running constantly without pause
• Frost or ice buildup inside that cannot be resolved 
• Inability to manually adjust temperature settings accurately

The Causes of thermostat failure can be age-related wear and tear, exposure to moisture or other environmental factors, or faulty internal components. 

This genuine OEM GE replacement is compatible with Hotpoint, RCA, and some Kenmore models.
 

This fresh food air tower assembly directs cold air circulation across the refrigerator fresh-food compartment to help maintain even temperatures and proper food storage. Replaces a damaged or cracked air tower to restore airflow distribution. What it does

• Channels chilled air from the evaporator to the fresh-food section for more even cooling.
• Helps eliminate warm spots and uneven cooling in refrigerator compartments.
• Replaces cracked, broken, or missing air guide components that can rattle or block airflow.
• Supports proper defrost and airflow patterns without altering cooling system components.

• One fresh food air tower assembly.

• Disconnect power before beginning any repair to avoid electrical shock.
• Remove shelves and food items for access; use gentle pressure to snap the tower into place or secure with manufacturer screws as required.
• Inspect surrounding mounting tabs and gaskets; replace any broken retainers to ensure correct fit and airflow.

The Glass Shelf is an OEM replacement part for GE refrigerators. It is designed to provide a sturdy and reliable surface for storing various food items inside the refrigerator.

A bad glass shelf can occur due to wear and tear, accidental damage, or misalignment. If you notice symptoms such as cracks, chips, or a sagging shelf, it may indicate a need to replace the glass shelf.

Signs of a faulty glass shelf include:

• Cracks or chips on the surface
• Sagging or instability
• Difficulty in storing or accessing items

Restore your GE refrigerator by replacing the faulty glass shelf with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This vegetable pan cover replaces a damaged or missing crisper cover to help contain humidity and keep produce organized in the refrigerator. It restores the sealed top for the vegetable/crisper pan so drawers close and stack properly. What it does:

• Covers the vegetable/crisper pan to help retain humidity and protect produce from odors.
• Provides a flat, stable surface so drawers and items above sit evenly.
• Prevents spills from splashing into lower compartments.
• Common signs you need this part: cracked or broken cover, warped fit, or a missing top for the vegetable pan.

• One vegetable/crisper pan cover (exact replacement part)

• Remove the crisper drawer before fitting the cover; align tabs and press into place until it snaps in.
• Inspect surrounding rails and tabs for damage before installing; replace any broken clips.
• Use gentle pressure—do not force; if it doesn't seat easily, re-check alignment.
• No special tools required; disconnecting power is not typically necessary but follow appliance safety precautions.

This replacement vegetable pan crisper restores the lower storage area in your refrigerator so produce sits securely and stays contained. A direct-fit inner drawer pan that helps keep fruits and vegetables organized and prevents spills. What it does:

• Provides a dedicated pan for storing vegetables and produce in the crisper compartment
• Holds and contains produce to prevent items from shifting or spilling onto shelves
• Replaces cracked, warped, or missing pans that can leak or fail to support contents
• Helps maintain an organized refrigerator interior for easier access to fresh foods

• One (1) vegetable pan crisper

• Remove food from the crisper area before installing; slide out the drawer and lift the old pan straight up to remove
• Align the replacement pan and lower it into place, then slide the drawer back in fully to fit
• Clean with mild soap and water; avoid abrasive cleaners or sharp tools that can scratch the surface

This vegetable pan is the replacement crisper drawer pan that holds produce in the refrigerator's fresh-food section, keeping fruits and vegetables organized and contained. It restores drawer storage when the original pan is cracked or missing. What it does:

• Serves as the lower bin/crisper to hold fruits and vegetables and keep them contained
• Replaces cracked, broken, warped, or missing pans that can no longer support stored produce
• Helps restore proper drawer function and organization in the fresh-food compartment
• Fits into existing tracks or supports used by the factory drawer assembly

• One vegetable (crisper) pan

• Remove food and the damaged pan, then slide the new pan into the existing tracks or supports
• No special tools typically required; handle carefully to avoid scratching or cracking the new pan
• Clean with mild soap and water before first use; do not use abrasive pads or harsh chemicals
• Wear gloves to protect hands from sharp edges during removal

The Electronic Defrost Timer is an OEM part for GE refrigerators. This part is responsible for regulating the automatic defrost cycle in your refrigerator. The defrost timer determines when to initiate the defrost cycle, allowing the freezer coils to thaw and eliminate any accumulated ice. It helps maintain cooling and prevents excessive frost from forming on the evaporator coils.

A bad electronic defrost timer can occur due to electrical malfunctions or wear and tear over time. If you notice symptoms such as excessive frost buildup, inconsistent cooling, or a constantly running freezer, it may be time to replace the defrost timer.

Symptoms of a bad electronic defrost timer include:

• Excessive frost buildup in the freezer
• Inconsistent cooling temperatures
• Freezer running continuously without cycling off

Restore your GE refrigerator's defrost cycle by replacing the faulty electronic defrost timer with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Capacitor is an OEM replacement part for GE refrigerators. It is part of the refrigerator's compressor motor, responsible for providing the initial energy needed to start the motor and keep it running smoothly. It stores electrical energy and releases it in a controlled manner to provide the necessary boost for the motor to start running.

A bad capacitor can occur due to electrical surges, component failure, or age-related degradation. If you notice symptoms such as the compressor not starting, frequent cycling on and off, or unusual humming or buzzing noises, it may indicate a need to replace the capacitor.

Symptoms of a bad capacitor include:

• Compressor not starting
• Frequent cycling on and off
• Unusual humming or buzzing noises

Restore your refrigerator's compressor motor by replacing the faulty capacitor with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This overload protector helps prevent compressor damage by shutting off electrical flow if the compressor overheats or draws excessive current. It restores normal operation when the motor cools, protecting the refrigeration system from electrical stress. What it does:

• Senses excessive current or overheating at the compressor and interrupts power to prevent damage
• Stops the compressor from running during an overheat condition to reduce risk of failure
• Common symptom: compressor hums but won't start or refrigerator isn't cooling reliably
• Be used with a separate start device; it protects the compressor motor itself

• Disconnect power to the appliance before accessing electrical components
• Note terminal positions and use proper connector tools to avoid loose connections
• Access typically requires removing rear service panel or compressor compartment cover

The Starter is an OEM part for GE refrigerators. It aids in starting the compressor, which is responsible for circulating refrigerant and maintaining the desired temperature inside the appliance.

A bad compressor starter can occur due to electrical issues, wear and tear, or component failure. If you notice symptoms such as the refrigerator not cooling properly, unusual noises coming from the compressor area, or the compressor not starting at all, it may indicate a faulty or malfunctioning starter.

Symptoms of a bad compressor starter include:

• Buzzing sound coming from the refrigerator
• Compressor not turning on or running intermittently
• Compressor not starting or running intermittently

Restore your refrigerator by replacing the faulty compressor starter with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This drain pan collects and channels defrost and condensation water away from the refrigerator compressor area to prevent pooling and water damage. It's a direct-fit replacement designed to restore proper drainage and help reduce unwanted leaks. What it does:

• Captures defrost and condensation water from the evaporator and directs it to the drain channel
• Prevents water from pooling under the refrigerator cabinet and on the floor
• Helps reduce musty odors caused by standing water in the cabinet cavity
• Restores proper clearance around the compressor area for normal operation

• One drain pan

• Disconnect power to the appliance before beginning any service
• Access typically requires removing the lower front grille or toe panel and sliding the refrigerator out to reach the pan
• Inspect and clear the drain tube and surrounding area of debris while the pan is removed

This cross-recessed hexagon bolt secures appliance components where a low-profile, cross-drive head and hex socket are required, restoring fit and preventing rattles or loose parts. Simple replacement for a single fastener. What it does:

• Fastens panels, brackets, or assemblies to hold parts securely in place.
• Stops vibration-related noise or movement caused by a loose or worn bolt.
• Provides a reliable drive profile for a screwdriver or bit to tighten or remove.
• Used wherever the appliance design specifies a cross-recessed hexagon head fastener.

• One hexagon bolt (cross-recessed) — only the bolt shown.

• Disconnect power and water before servicing to avoid shock or injury.
• Match the bolt location and orientation; hand-start threads to avoid cross-threading.
• Tighten snugly but do not overtighten — excessive force can strip threads or damage components.
• Use the correct screwdriver/bit size for a clean engagement with the cross recess.

A replacement middle hinge plug (button) that covers the refrigerator's center hinge area for a neat, finished appearance and helps keep dirt and moisture out of the hinge cavity. What it does:

• Covers the middle hinge opening to protect hinge components from dirt and debris
• Restores the appliance's finished look after a broken or missing plug
• Helps reduce exposure of the hinge to moisture that can accelerate wear
• Can prevent small items from getting caught in the hinge cavity and affecting operation

• Typically snaps into the hinge opening—no special tools required for most models
• Align plug with the hinge cavity and press firmly until it seats; avoid forcing to prevent damage
• Remove/install the plug as directed by your service manual

A replacement plastic top hinge cover that restores the finished look and protects the refrigerator hinge area from dust, dirt and accidental contact. Helps hide hardware and prevents debris buildup at the door pivot. What it does

• Covers and protects the top hinge assembly from dust, spills and incidental contact.
• Restores finished appearance when the original cover is cracked, broken or missing.
• Helps prevent dirt and debris from interfering with hinge operation.
• Reduces sharp edges or exposed hardware that can catch clothing or fingers.

• High-level task: access requires removing the door or lifting it slightly to relieve hinge pressure.
• Always support the door when removing or installing hinge components to avoid injury or damage.
• Unplug the appliance or shut off power to avoid unexpected operation while working on the door area.
• Inspect hinge fasteners and surrounding trim during installation; replace any damaged hardware as needed.

This wiring box cover protects the appliance's terminal block and wiring junction, keeping wires secure and reducing exposure to electrical contacts. It restores a finished, safe access point for the wiring compartment. What it does:

• Covers and protects the terminal block/wiring junction from accidental contact
• Helps keep dust and debris out of the wiring compartment
• Secures wiring in place to prevent snagging or strain on connections
• Restores the factory access cover for safe servicing and operation

• One wiring box cover

• Disconnect power to the appliance before starting any work
• Use basic hand tools (screwdriver) to remove the old cover and fasten the replacement
• Ensure all wires and terminals are tucked safely inside the box before installing the cover
• If terminals or wiring are damaged, replace or repair them before re-applying power.

The Evaporator Fan Motor is an OEM replacement part for Whirlpool refrigerators. It is responsible for powering the evaporator fan to circulate air. Over time, the motor can fail due to wear and tear. Causes of a bad evaporator fan motor include seized bearings, electrical shorts, and worn out windings.

Symptoms of a failed motor:

• No cold air circulation
• Lack of airflow
• Excessive frost and ice buildup
• Fluctuating temperatures

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This evaporator fan bracket secures the evaporator fan motor and blade assembly inside the freezer compartment so the fan runs steadily and quietly. It restores proper airflow support for efficient cooling. What it does:

• Holds the evaporator fan motor and blade in the correct position so air circulates across the evaporator coil
• Prevents excess vibration and noise from a loose fan assembly
• Helps maintain consistent freezer temperature by keeping the fan aligned and stable
• If the original bracket is cracked, broken, or missing

• One evaporator fan bracket

• Disconnect power to the appliance before beginning any work
• Access may require removing interior panels and defrosting if frost blocks the area
• Handle the evaporator coil and nearby tubing gently to avoid damage
• Secure bracket with the original fasteners; inspect fan motor and blade for damage while replacing

This evaporator defrost harness connects the defrost heater and thermostat to the fridge's wiring, restoring the defrost circuit so frost doesn't build on evaporator coils. It's a direct-replacement electrical harness for defrost system repairs. What it does:

• Routes power and signals between the defrost heater, thermostat/DFT and main wiring
• Enables the defrost cycle so ice buildup on the evaporator is cleared
• Helps stop recurring frost/ice on coils that can reduce cooling efficiency
• Commonly replaced when connectors are damaged, corroded, or wires are broken

• One evaporator defrost harness

• Disconnect power to the appliance before beginning any work to avoid electric shock
• Handle evaporator area carefully — sharp fins and edges can cause injury
• Route and secure the harness to match original routing; ensure connectors seat fully

This defrost heater melts frost and ice from the evaporator to restore proper airflow and cooling in frost-prone refrigerators. It helps prevent heavy ice buildup that can reduce cooling efficiency and cause temperature problems. What it does:

• Warms the evaporator coil during the defrost cycle to remove accumulated frost and ice
• Restores normal airflow through the evaporator so the refrigerator can cool properly
• Common symptom: visible ice buildup on the evaporator or reduced cooling performance
• Common symptom: refrigerator runs longer than normal or fails to maintain set temperature

• One defrost heater assembly

• Always disconnect power to the appliance before servicing to avoid shock hazard
• Handle the evaporator and heater carefully to avoid damaging coils or wiring
• Verify continuity of the heater with a multimeter before and after installation
• If recurring icing occurs, inspect and test the defrost thermostat, timer, and control components

The Drier is an OEM component specifically designed for GE combination refrigerator-freezers. Absorbing moisture, its treated silica particles buffer humidity within refrigerant lines. Proper drying sustains energy-efficient performance while preventing corrosion.

Causes of a faulty drier commonly relate to saturation reducing capacity. As desiccant degrades, water passes into closed system compressors requiring change. 

Symptoms of a bad drier involve:

• Frost and ice buildup impairing cooling  
• Puddling around evaporator evidencing leaks
• Higher operating costs from impaired efficiency

Causes of a bad drier involve typical saturation shortening drying cycles. Cracks release desiccant particles risking blockages necessitating timely replacement.

This OEM GE part is also compatible with some Hotpoint, RCA, and Frigidaire combination units. Replace to retain steady humidity management protecting components and maximizing freshness years of operation.
 

The R600 Process Valve with Red Cap is an OEM part for GE refrigerators. It regulates the flow of refrigerant within the cooling system, ensuring proper cooling and temperature control.

A bad process valve can occur due to wear and tear, refrigerant leaks, or mechanical failure. If you notice symptoms such as inadequate cooling, excessive frost buildup, or unusual noises coming from the refrigerator, it may indicate a faulty or malfunctioning process valve.

Symptoms of a bad process valve include:

• Inadequate cooling or inconsistent temperature control
• Excessive frost buildup in the freezer
• Unusual noises coming from the refrigerator

Restore your refrigerator by replacing the faulty process valve with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This is a replacement mounting screw used to secure components inside compatible GE appliances. It restores proper fastening where the original screw is missing, stripped, or damaged so parts stay aligned and operate safely. What it does:

• Fastens trim panels, brackets, or internal components to appliance cabinet and chassis
• Replaces missing or damaged screws that can cause rattling, misalignment, or loose parts
• Helps maintain proper component alignment for reliable operation
• Simple hardware repair to restore original fit where the factory screw is lost or worn

• Verify screw size and thread match the original before installation
• Use correct driver to avoid stripping the head; tighten until snug but do not overtighten
• Disconnect power to the appliance before working near electrical components