Parts for Hot Point HPS10LSVBRSS: Cabinet Parts

This is a replacement evaporator cover screw that secures the evaporator cover/trim in the refrigerator evaporator compartment, restoring proper panel fit and helping maintain airflow and temperature control. What it does:

• Fastens the evaporator cover or trim to the evaporator housing or cabinet
• Keeps the evaporator cover secure to prevent rattling and air leaks
• Helps maintain correct airflow over the evaporator for consistent cooling
• Small hardware solution for loose or missing evaporator cover mounting points

• One evaporator cover screw (quantity: 1)

• Intended for use where the evaporator cover screw is missing, stripped, or damaged
• Use matching screwdriver/drill bit and avoid over-tightening to prevent stripping the hole or cracking plastic trim
• Disconnect power to the appliance before accessing internal components and work with caution around sharp sheet metal and cold evaporator surfaces

This air duct cover directs cold air through the refrigerator compartment and helps keep airflow even for consistent cooling. It replaces a cracked, broken or missing duct housing to restore proper air circulation. What it does

• Guides cold air from the evaporator into the fresh-food compartment to help maintain temperature balance
• Helps prevent frost and cold-air leakage caused by damaged or loose ducting
• Can reduce uneven cooling or warm spots when the original cover is damaged
• Fits where the air path is sealed or routed through the freezer/refrigerator cavity

• One air duct cover

• Disconnect power to the appliance before beginning any work
• Access typically requires removing interior shelves, drawers or a rear freezer panel; keep fasteners for reassembly
• Handle plastic parts carefully to avoid cracking; align tabs/clips before fastening
• Restore power and verify normal airflow and temperatures after installation

Fix inconsistent refrigerator temperatures with this cold control housing duct. Directs airflow around the thermostat to maintain proper cooling control.

Refrigerator too warm or running constantly? This cold control thermostat regulates temperature by cycling the compressor on and off as needed.

LED light board assembly for top-mount refrigerators. Installs inside the fresh food or freezer compartment. Replace when board is cracked or damaged.

This fresh food air tower assembly directs cold air circulation across the refrigerator fresh-food compartment to help maintain even temperatures and proper food storage. Replaces a damaged or cracked air tower to restore airflow distribution. What it does

• Channels chilled air from the evaporator to the fresh-food section for more even cooling.
• Helps eliminate warm spots and uneven cooling in refrigerator compartments.
• Replaces cracked, broken, or missing air guide components that can rattle or block airflow.
• Supports proper defrost and airflow patterns without altering cooling system components.

• One fresh food air tower assembly.

• Disconnect power before beginning any repair to avoid electrical shock.
• Remove shelves and food items for access; use gentle pressure to snap the tower into place or secure with manufacturer screws as required.
• Inspect surrounding mounting tabs and gaskets; replace any broken retainers to ensure correct fit and airflow.

Replace a cracked, chipped, or broken glass shelf in your top-mount refrigerator. This shelf provides a sturdy storage surface for food and beverages.

Replace your damaged crisper drawer cover to maintain humidity control and keep produce fresh. Restores proper drawer stacking. Verify fit with your model.

Replace your cracked or broken refrigerator crisper drawer pan. This inner vegetable bin keeps produce organized and contained in the lower storage area.

Replacement crisper drawer pan for refrigerator fresh-food section. Holds and organizes produce. Needed when original pan is cracked, broken, or missing.

Fix a refrigerator not defrosting with this electronic defrost timer. Regulates automatic defrost cycles to prevent ice buildup on freezer coils.

The Capacitor is an OEM replacement part for GE refrigerators. It is part of the refrigerator's compressor motor, responsible for providing the initial energy needed to start the motor and keep it running smoothly. It stores electrical energy and releases it in a controlled manner to provide the necessary boost for the motor to start running.

A bad capacitor can occur due to electrical surges, component failure, or age-related degradation. If you notice symptoms such as the compressor not starting, frequent cycling on and off, or unusual humming or buzzing noises, it may indicate a need to replace the capacitor.

Symptoms of a bad capacitor include:

• Compressor not starting
• Frequent cycling on and off
• Unusual humming or buzzing noises

Restore your refrigerator's compressor motor by replacing the faulty capacitor with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This overload protector helps prevent compressor damage by shutting off electrical flow if the compressor overheats or draws excessive current. It restores normal operation when the motor cools, protecting the refrigeration system from electrical stress. What it does:

• Senses excessive current or overheating at the compressor and interrupts power to prevent damage
• Stops the compressor from running during an overheat condition to reduce risk of failure
• Common symptom: compressor hums but won't start or refrigerator isn't cooling reliably
• Be used with a separate start device; it protects the compressor motor itself

• Disconnect power to the appliance before accessing electrical components
• Note terminal positions and use proper connector tools to avoid loose connections
• Access typically requires removing rear service panel or compressor compartment cover

Fix a refrigerator that won't cool or run with this compressor starter. Essential for starting the compressor that circulates refrigerant. Direct fit.

Water pooling under your refrigerator? This drain pan collects defrost water and prevents leaks. Direct-fit replacement restores proper drainage.

Left leveling leg for refrigerators. Supports and levels your appliance for proper door alignment. Replace if cracked, broken, or missing.

Right-side leveling leg for refrigerators. Installs at the front or rear corner to adjust height and stability. Replace if cracked, broken, or missing.

This cross-recessed hexagon bolt secures appliance components where a low-profile, cross-drive head and hex socket are required, restoring fit and preventing rattles or loose parts. Simple replacement for a single fastener. What it does:

• Fastens panels, brackets, or assemblies to hold parts securely in place.
• Stops vibration-related noise or movement caused by a loose or worn bolt.
• Provides a reliable drive profile for a screwdriver or bit to tighten or remove.
• Used wherever the appliance design specifies a cross-recessed hexagon head fastener.

• One hexagon bolt (cross-recessed) — only the bolt shown.

• Disconnect power and water before servicing to avoid shock or injury.
• Match the bolt location and orientation; hand-start threads to avoid cross-threading.
• Tighten snugly but do not overtighten — excessive force can strip threads or damage components.
• Use the correct screwdriver/bit size for a clean engagement with the cross recess.

A replacement middle hinge plug (button) that covers the refrigerator's center hinge area for a neat, finished appearance and helps keep dirt and moisture out of the hinge cavity. What it does:

• Covers the middle hinge opening to protect hinge components from dirt and debris
• Restores the appliance's finished look after a broken or missing plug
• Helps reduce exposure of the hinge to moisture that can accelerate wear
• Can prevent small items from getting caught in the hinge cavity and affecting operation

• Typically snaps into the hinge opening—no special tools required for most models
• Align plug with the hinge cavity and press firmly until it seats; avoid forcing to prevent damage
• Remove/install the plug as directed by your service manual

A replacement plastic top hinge cover that restores the finished look and protects the refrigerator hinge area from dust, dirt and accidental contact. Helps hide hardware and prevents debris buildup at the door pivot. What it does

• Covers and protects the top hinge assembly from dust, spills and incidental contact.
• Restores finished appearance when the original cover is cracked, broken or missing.
• Helps prevent dirt and debris from interfering with hinge operation.
• Reduces sharp edges or exposed hardware that can catch clothing or fingers.

• High-level task: access requires removing the door or lifting it slightly to relieve hinge pressure.
• Always support the door when removing or installing hinge components to avoid injury or damage.
• Unplug the appliance or shut off power to avoid unexpected operation while working on the door area.
• Inspect hinge fasteners and surrounding trim during installation; replace any damaged hardware as needed.

This wiring box cover protects the appliance's terminal block and wiring junction, keeping wires secure and reducing exposure to electrical contacts. It restores a finished, safe access point for the wiring compartment. What it does:

• Covers and protects the terminal block/wiring junction from accidental contact
• Helps keep dust and debris out of the wiring compartment
• Secures wiring in place to prevent snagging or strain on connections
• Restores the factory access cover for safe servicing and operation

• One wiring box cover

• Disconnect power to the appliance before starting any work
• Use basic hand tools (screwdriver) to remove the old cover and fasten the replacement
• Ensure all wires and terminals are tucked safely inside the box before installing the cover
• If terminals or wiring are damaged, replace or repair them before re-applying power.

Fix a refrigerator that's not cooling or making unusual noises with a new evaporator fan motor. Circulates cold air throughout the fridge compartment.

Fix noisy freezer fan or uneven cooling. This evaporator fan bracket secures the motor and blade assembly for steady airflow and quiet operation.

Frost building up on evaporator coils? This defrost harness reconnects the heater and thermostat to restore the defrost circuit. Direct replacement part.

This defrost heater melts frost and ice from the evaporator to restore proper airflow and cooling in frost-prone refrigerators. It helps prevent heavy ice buildup that can reduce cooling efficiency and cause temperature problems. What it does:

• Warms the evaporator coil during the defrost cycle to remove accumulated frost and ice
• Restores normal airflow through the evaporator so the refrigerator can cool properly
• Common symptom: visible ice buildup on the evaporator or reduced cooling performance
• Common symptom: refrigerator runs longer than normal or fails to maintain set temperature

• One defrost heater assembly

• Always disconnect power to the appliance before servicing to avoid shock hazard
• Handle the evaporator and heater carefully to avoid damaging coils or wiring
• Verify continuity of the heater with a multimeter before and after installation
• If recurring icing occurs, inspect and test the defrost thermostat, timer, and control components

Fix refrigerant flow issues and moisture contamination in your refrigerator's sealed system. This filter drier requires EPA-certified tech for installation.

Fix cooling issues in your refrigerator with this process valve. Regulates refrigerant flow for proper temperature control. Red cap design for R600 systems.

Fix a refrigerator light that won't turn on or off with this door-activated light switch. Simple DIY repair taking 15-30 minutes with basic tools.

This is a replacement mounting screw used to secure components inside compatible GE appliances. It restores proper fastening where the original screw is missing, stripped, or damaged so parts stay aligned and operate safely. What it does:

• Fastens trim panels, brackets, or internal components to appliance cabinet and chassis
• Replaces missing or damaged screws that can cause rattling, misalignment, or loose parts
• Helps maintain proper component alignment for reliable operation
• Simple hardware repair to restore original fit where the factory screw is lost or worn

• Verify screw size and thread match the original before installation
• Use correct driver to avoid stripping the head; tighten until snug but do not overtighten
• Disconnect power to the appliance before working near electrical components