Parts for Kelvinator KCNF070QWA: Cabinet Parts

This temperature control is the refrigerator thermostat that lets the appliance monitor and regulate internal cooling for stable food temperatures. It replaces a worn or faulty control to restore reliable temperature adjustments. What it does:

• Senses internal temperature and signals the cooling system to cycle on and off
• Restores user temperature setting responsiveness when the fridge is running too cold, too warm, or not cycling
• Helps prevent compressor from running continuously by enabling proper on/off cycling
• Works as the user-facing control for adjusting internal temperature setpoints

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Handle wiring harness and terminals carefully; match wire locations during reassembly.
• Minor disassembly of the control panel may be required; keep fasteners organized.

This small cabinet corner bracket secures and protects the refrigerator cabinet corner, helping keep panels aligned and preventing edge damage. It's a simple replacement that restores proper fit and reduces gaps or rubbing at the corner. What it does:

• Supports and stabilizes the cabinet corner to maintain panel alignment
• Prevents cabinet edge damage and wear from contact or stress
• Helps reduce rattling or movement at the corner area
• Can correct minor fit or gap issues caused by a broken or missing corner piece

• Disconnect power before servicing the appliance to avoid shock
• Inspect surrounding trim and fasteners; reuse original screws if undamaged
• Handle trim carefully to avoid scratching
• If fit or attachment points are damaged, additional repairs may be needed

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

The insert nut provides a durable threaded anchor in thin metal or plastic panels. It lets mounting screws tighten securely so covers, brackets, or trim stay fastened and aligned without loosening from vibration.

• Adds internal threads in a thin panel so a machine screw can be used
• Secures panels, brackets, or trim to the appliance cabinet or frame
• Replaces a stripped, damaged, or missing insert to restore screw retention
• Symptoms addressed: screws won't tighten, hardware falls out, panel rattles or shifts

• Disconnect power to the appliance before servicing; shut off water or gas supply if applicable
• Access the mounting location; remove the screw and the old insert if present
• Position the new insert squarely in the hole/slot and press or snap into place as designed
• Reinstall the screw and tighten snugly—do not overtighten to avoid stripping the insert or panel

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

This wire guard is a replacement protective grille that shields refrigerator fan and condenser components from debris while helping prevent accidental contact. It restores proper airflow protection and keeps internal parts accessible for service. What it does

• Covers and protects fan/condenser area from large debris and objects
• Helps prevent accidental contact with rotating fan blades
• Maintains unobstructed airflow through the condenser/fan assembly
• Useful when the original guard is cracked, bent, or missing

• One wire guard

• Designed for direct replacement using existing mounting points;
• Disconnect power to the appliance before beginning any service
• Use appropriate hand tools; avoid over-tightening fasteners to prevent damage
• If corrosion, mounting clips, or adjacent components are damaged, replace those parts as needed

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener