Parts for Kenmore 253.12912410 (25312912410, 253 12912410): Cabinet Parts

This temperature control knob replaces a worn or missing knob so you can easily adjust the cold-control setting. Restores smooth, precise temperature adjustments and a clean, factory look. What it does:

• Attaches to the cold-control (thermostat) shaft to change the temperature setting
• Provides secure grip and pointer alignment for accurate selections
• Typical failure symptoms: cracked or missing knob, stripped hub, or a knob that slips or won't turn the control

• 1 temperature control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying at an angle to prevent shaft damage
• Align the shaft shape with the new knob and press firmly until fully seated
• The pointer aligns with the control graphics after installation

This temperature control is the refrigerator thermostat that lets the appliance monitor and regulate internal cooling for stable food temperatures. It replaces a worn or faulty control to restore reliable temperature adjustments. What it does:

• Senses internal temperature and signals the cooling system to cycle on and off
• Restores user temperature setting responsiveness when the fridge is running too cold, too warm, or not cycling
• Helps prevent compressor from running continuously by enabling proper on/off cycling
• Works as the user-facing control for adjusting internal temperature setpoints

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Handle wiring harness and terminals carefully; match wire locations during reassembly.
• Minor disassembly of the control panel may be required; keep fasteners organized.

This small cabinet corner bracket secures and protects the refrigerator cabinet corner, helping keep panels aligned and preventing edge damage. It's a simple replacement that restores proper fit and reduces gaps or rubbing at the corner. What it does:

• Supports and stabilizes the cabinet corner to maintain panel alignment
• Prevents cabinet edge damage and wear from contact or stress
• Helps reduce rattling or movement at the corner area
• Can correct minor fit or gap issues caused by a broken or missing corner piece

• Disconnect power before servicing the appliance to avoid shock
• Inspect surrounding trim and fasteners; reuse original screws if undamaged
• Handle trim carefully to avoid scratching
• If fit or attachment points are damaged, additional repairs may be needed

The Freezer Basket is an OEM part for Frigidaire freezers. It provides organized storage space within the freezer, allowing for easy access and efficient use of the freezer's capacity by keeping items contained and separated. It measures approximately 18 x 11 inches. 

You should replace the freezer basket if it becomes bent, rusted, or damaged. Causes of a bad freezer basket can include overloading with heavy items, prolonged exposure to moisture leading to rust, or damage from accidental impacts during loading or unloading.

Symptoms of a bad freezer basket include:

• Difficulty sliding the basket in and out
• Visible rust or corrosion
• The basket not sitting properly in its tracks
• Bent or broken wires compromising the basket's structure

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This panel-mounted signal light is the small indicator lamp that illuminates when a function is active. It restores clear visual status on the control panel so you can tell at a glance when the appliance is operating. What it does:

• Lights to indicate when a feature, cycle, or function is on (model-dependent)
• Restores visible status feedback on the console or control panel
• Helps alert you if a function remains active after use
• Addresses issues such as no light, constant-on light, flickering, or a damaged lens

• 1 signal light

• Disconnect power at the breaker before servicing
• Access the control panel/console; remove knobs and screws as needed
• Note wire positions or take a photo; transfer wires to the new light
• Secure the light in the panel, reassemble, restore power, and test

This adhesive-backed plastic mounting clip secures wires, small hoses, or components inside appliances to reduce movement and rattling. Its low-profile design helps keep internal parts organized for quieter, safer operation. What it does:

• Holds wiring harnesses, sensor leads, or small tubing in place to prevent chafing and noise
• Reduces vibration-related contact that can cause intermittent electrical or sensor issues
• Provides a simple, non-invasive mounting point without drilling or fasteners
• Adhesive backing allows quick placement in tight or hard-to-reach areas

• Clean and dry mounting surface; remove backing and press clip firmly for full adhesion
• Allow adhesive to set per ambient temperature (avoid stress on clip during initial cure)
• Disconnect power before installing
• Replace any brittle or damaged surrounding insulation or wire loom as needed

This wire guard is a replacement protective grille that shields refrigerator fan and condenser components from debris while helping prevent accidental contact. It restores proper airflow protection and keeps internal parts accessible for service. What it does

• Covers and protects fan/condenser area from large debris and objects
• Helps prevent accidental contact with rotating fan blades
• Maintains unobstructed airflow through the condenser/fan assembly
• Useful when the original guard is cracked, bent, or missing

• One wire guard

• Designed for direct replacement using existing mounting points;
• Disconnect power to the appliance before beginning any service
• Use appropriate hand tools; avoid over-tightening fasteners to prevent damage
• If corrosion, mounting clips, or adjacent components are damaged, replace those parts as needed

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener