Parts for Whirlpool XHPC155XW0: 01 - Cabinet Parts

This drawer front assembly replaces a damaged or worn refrigerator drawer front to restore proper fit, appearance and basic operation. It gives the drawer a finished face and lets the drawer open and close as intended. What it does:

• Replaces a cracked, dented or cosmetically damaged drawer front
• Restores proper alignment and basic drawer movement
• Helps keep stored items contained and accessible
• Returns the appliance's original appearance at the front of the drawer

• Disconnect power to the appliance before starting work for safety.
• Remove contents and take out the drawer to access mounting hardware.
• Keep original fasteners; transfer brackets or clips as required—only install parts explicitly shown in your model's diagram.
• If any mounting clips, trim or hardware are damaged, replace them with the exact parts specified for your model.

This outer front panel restores the washer/dryer cabinet's appearance and protects internal components from debris and damage. It provides a clean, finished look and supports correct alignment of the door and control area. What it does:

• Replaces a cracked, dented or bent front panel to restore cabinet integrity and appearance
• Shields internal parts from dust, lint and moisture that can cause premature wear
• Helps maintain proper door alignment and sealing for consistent operation
• Reduces vibration-related noise by securing the front of the cabinet

• One outer front panel

• Disconnect power (and water supply for washers) before beginning any repair
• Remove console, door and any retaining screws or clips as needed to access the front panel
• Handle the panel carefully to avoid scratching the finish; use appropriate fasteners and torque per OEM guidance

This is the center divider for a laundry pedestal drawer. It slots into the drawer to create a middle partition, keeping detergents and supplies upright and organized so items don't slide around when the drawer opens and closes.

• Divides the pedestal storage drawer into sections for better organization
• Helps keep bottles and boxes upright to reduce shifting and rattling
• Restores proper fit and function when the original divider is missing or broken
• Typical signs you need this part: items sliding around, difficulty organizing, or a cracked/missing divider

• Empty the pedestal drawer before starting
• Fully extend the drawer and locate the factory slots/guides
• Align the divider tabs with the slots and press firmly until seated
• Check that the divider is secure and the drawer opens/closes smoothly; use care to avoid pinched fingers

This slide assembly restores smooth, reliable opening and closing for a pedestal storage drawer. It replaces worn or damaged slide hardware so the drawer operates quietly and stays aligned during use. What it does:

• Guides and supports the pedestal drawer for stable, even travel
• Prevents drawer sagging, sticking, or binding when loading/unloading
• Reduces rattling or grinding noises caused by worn slides
• Helps maintain proper drawer alignment and secure closure

• Disconnect power to the appliance and remove the pedestal drawer per the appliance manual before starting.
• Remove the old slide hardware, retain any reusable fasteners, and compare parts for correct orientation.
• Align the new slide, secure with the correct screws, and reassemble the drawer; test full travel and smooth operation.

This factory screw secures appliance components such as panels, brackets, and trim. It replaces missing, stripped, or damaged hardware to restore a tight, rattle-free fit and proper alignment in the specified location for your model.

• Fastens covers, panels, brackets, or trim as specified in the parts diagram
• Restores secure fit when an original screw is missing or damaged
• Helps reduce vibration, rattling, and looseness
• Direct-fit hardware specified by the manufacturer for the original location

• Disconnect power and shut off water/gas before servicing
• Verify the screw's location in your model's parts diagram before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver/bit and avoid overtightening into plastic to prevent stripping

Single unit. Includes foot pad.

This is a replacement mounting screw used to secure panels and components on compatible Whirlpool appliances, restoring loose or missing fasteners for safe, stable operation. What it does

• Fastens appliance panels, brackets, and small components in place
• Replaces stripped, rusted, or missing screws that cause rattling or loose parts
• Helps restore proper alignment and reduce vibration-related noise
• Matches OEM fit and function for straightforward replacement

• One replacement screw

• Use the matching screwdriver or nut driver to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or panel damage
• Turn off and unplug the appliance before accessing internal components

Number-8, 18-thread screw used to secure panels, brackets and small assemblies in Whirlpool appliances. Replacing a missing or damaged screw restores secure mounting and helps stop rattling or loose parts. What it does:

• Fastens trim, panels, brackets or small appliance components that use a #8-18 threaded fastener
• Restores secure mounting when a screw is lost, stripped or damaged
• Helps eliminate vibration-related noise from loose parts
• Simple replacement part for basic fastening needs

• Disconnect power to the appliance before servicing and work on a cool, stable surface
• Use the correct screwdriver or driver bit to avoid cam-out or stripped heads
• Thread in straight and tighten until snug; do not over-torque to avoid stripping threads or damaging components
• Replace with the identical screw type and size for proper fit and function

This round spacer pad cushions and separates contacting parts inside your appliance to maintain proper alignment and help reduce noise and wear. Replacing a worn or missing pad restores smooth, quiet operation and protects adjacent components. What it does:

• Maintains correct spacing between mating parts to prevent rubbing
• Dampens minor vibration and impact to reduce squeaks or rattles
• Helps protect finishes and edges from scuffs or chips at contact points
• Common signs of failure: pad is missing, flattened, hardened/cracked, or you notice harsher contact and new noises

• Disconnect power before servicing
• Use your model's parts diagram to locate the pad's position and quantity used
• Match placement/orientation to the original; install in the same position
• Clean the contact surface so the pad seats flat and adheres or fits properly

This handle assembly attaches to the storage drawer on a laundry pedestal, providing a solid, comfortable grip. Replace a cracked, loose, or missing handle to restore smooth drawer operation and the pedestal's original, finished appearance.

• Mounts to the pedestal drawer front and serves as the user pull
• Helps ensure consistent, easy opening and closing of the storage drawer
• Typical failure symptoms: cracked or broken handle, loose handle, difficulty opening the drawer
• Restores proper fit and appearance after damage or wear

• Disconnect power and remove drawer contents before beginning
• Remove the drawer to access the handle fasteners; place it on a protected surface
• Remove fasteners, align the new handle, and secure; reuse existing hardware if in good condition
• Test drawer operation and avoid overtightening screws

This touch-up paint restores small chips and scratches on painted appliance surfaces to improve appearance and slow corrosion. It's a simple cosmetic repair that helps appliances look cared-for between major services. What it does:

• Covers minor paint chips, nicks and surface scratches
• Helps restore a uniform finish on exterior panels and trim
• Reduces likelihood of surface rust where bare metal is exposed
• Ideal for spot repairs on visible areas without repainting large panels

• One touch-up paint item for appliance finish

• Work in a well-ventilated area and protect surrounding surfaces
• Shake well and test on an inconspicuous spot before applying
• Apply sparingly in thin coats; allow each coat to dry per product instructions
• Keep out of reach of children and away from open flame

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

The Appliance Touchup Paint is an OEM product for Whirlpool appliances. This touchup paint is used to cover scratches, chips, and minor blemishes on the surface of various appliances, helping to maintain their appearance and protect them from rust and other damage. It is specifically formulated to match the original color and finish of Whirlpool appliances, ensuring a seamless repair.

Causes of needing touchup paint include everyday wear and tear, accidental impacts that cause chipping or scratching, and exposure to harsh cleaning chemicals that can damage the finish. Regular use of touchup paint can help keep appliances looking new and extend their lifespan.

Symptoms indicating the need for Appliance Touchup Paint include:

• Visible scratches or chips on the appliance surface
• Areas of exposed metal prone to rust
• Blemishes that affect the overall aesthetic of the appliance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: White. Size: 13 oz can. Acrylic appliance aerosol can spray paint.

The Appliance Spray Paint is an OEM part for Whirlpool appliances, designed to provide a quick and effective way to touch up or completely refinish the exterior of various appliances. This specialty spray paint is formulated to adhere to metal surfaces, offering a durable and resistant finish that can withstand the routine wear and tear of kitchen environments, including heat, moisture, and everyday use.

The primary reason for using such a specialized paint is to maintain or restore the aesthetic appeal of your appliances while protecting them from further damage. 

Symptoms needing for Appliance Spray Paint include:

• Scratches, chips, or rust spots on the appliance's exterior that can lead to further damage or corrosion if left untreated
• A desire to refresh or update the appearance of the appliance without the need for complete replacement
• Discoloration or fading of the original finish due to age, exposure to sunlight, or cleaning agents

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.