Parts for Ge WPDH8800J2MV: 02 - Cabinet & Top Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a replacement ST4-10 appliance screw used to fasten interior and exterior components. It provides a secure, corrosion-resistant hold to keep panels, brackets, and assemblies in place during normal appliance operation. What it does:

• Secures trim, panels, brackets, and small assemblies that use ST4-10 sheet-metal style screws
• Restores loose or missing fasteners that can cause rattling, misalignment, or part movement
• Small, high-thread engagement helps maintain a tight fit in threaded or self-tapping holes

• One ST4-10 screw

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Handle small parts carefully and keep track of fasteners during disassembly

Replacement mounting screw for washers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

Replacement mounting screw for washer pedestals. Secures pedestal to washer base. Order if original screw is stripped, missing, or damaged.

EMI filter installs where power cord enters washer to reduce electrical noise on incoming power line. Replace if cracked, damaged, or causing interference.

Washer top panel assembly that covers and protects the upper cabinet. Replace if your existing panel is cracked, dented, discolored, or missing.

The Water Inlet Valve is an OEM part for GE washing machines. It controls the flow of water into the washer during the fill cycles. The valve opens and closes to allow the correct amount of water to enter the machine based on the selected wash cycle and settings.

You should replace this water inlet valve if it becomes defective. A bad water inlet valve can cause several issues such as improper water levels, slow filling, or no water entering the washer at all. These problems can be due to sediment build-up, electrical faults, or mechanical wear.

Symptoms of a bad water inlet valve include:

• Washer not filling with water
• Slow filling or low water pressure
• Leaking or dripping water from the valve area
• Incorrect water levels in the drum

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This spring hanger secures a suspension spring to the washer's cabinet/frame, supporting the tub assembly and helping control vibration. Replace a cracked or broken hanger to restore stable spin performance and reduce banging or shaking.

• Provides the mounting point for a suspension spring that helps carry the tub's weight
• Helps keep the basket balanced and limits vibration during spin
• Failure symptoms can include excessive shaking, loud banging, out-of-balance stops, or a sagging/leaning tub
• Visible cracks, deformation, or broken mounting tabs indicate the hanger should be replaced

• Disconnect power and water supply; access the hanger location per your model's service procedure
• Support the tub and control spring tension with locking pliers; wear gloves and eye protection
• Move the suspension spring to the new hanger and secure it in the same orientation
• Reassemble, level the washer, and run a test spin to verify smooth operation

This top panel pin secures the range's upper/top panel to the appliance frame so the panel stays aligned and stable for safe, reliable use. It's a simple replacement part that restores proper panel fit and reduces rattling. What it does:

• Locks the top/upper panel into position to keep it from shifting or sagging
• Helps eliminate panel movement, noise, and misalignment during use
• Restores a secure fit if the original pin is broken, bent, or missing
• Works as a direct-fit replacement where this OEM pin is specified

• One top panel pin

• Disconnect power to the appliance before any service to avoid shock or injury
• Access may require removing the cooktop or backguard
• Inspect surrounding clips, hinges, and mounting points and replace if damaged

This is a self-tapping appliance screw used to fasten panels and small components. It replaces missing or damaged screws to restore secure fit and reduce rattling or loose parts. What it does:

• Secures trim, panels, brackets or components where a small self-tapping fastener is required
• Restores a tight fit to stop vibration, rattling or misalignment
• Replaces stripped, corroded or lost screws that prevent proper assembly
• Compatible with common appliance sheet-metal and plastic thread-in points

• Use the proper screwdriver or driver bit to avoid stripping the head
• Start threads straight and apply firm, controlled pressure when driving into thin metal or plastic
• Replace with the exact size and type to ensure correct fit and function
• Disconnect power and follow appliance-specific safety instructions before servicing

This front panel pin secures a range or appliance control/front panel to the cabinet, keeping the panel aligned and stable for safe operation. It's a small but important fastener that prevents panel sag and rattles. What it does:

• Secures the front/control panel to the appliance cabinet so the panel stays in place
• Keeps panel edges aligned for a clean fit and proper button/knob operation
• Prevents vibration noise or rattling caused by a loose or broken pin
• A worn or broken pin can allow the panel to move, feel loose, or misalign

• One front panel pin

• Disconnect power to the appliance before beginning any repair
• Typically accessed by removing the console or front panel screws; retain screws and small parts
• Replace the pin carefully to avoid damaging the panel or surrounding trim

Secures your washer's front service panel to prevent vibration and sagging. Replace if panel is loose or misaligned. Confirm fit with your model number.

This genuine replacement screw secures panels and components on compatible appliances to restore proper fit and reduce vibration or rattling. Use when missing, stripped, or loose fasteners prevent parts from staying in place. What it does

• Fastens trim, panels, or mounting brackets to maintain component alignment
• Restores secure attachment when original screws are missing or damaged
• Helps eliminate noise and vibration caused by loose parts
• Matches the OEM thread profile and length for proper fit

• Use the correct screwdriver or bit to avoid cam-out and damaged heads
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep spare screws and small parts away from children and pets
• If threads are damaged, replace mating fastener or insert rather than forcing this screw

Fix a washer that won't drain or leaves clothes soaking wet. This drain pump removes water during the drain cycle. DIY-friendly, about 1 hour to install.

This screw with attached washer secures internal components in your washer. Replace if screw is stripped, missing, or washer is damaged or worn out.

This inverter connector links the refrigerator's inverter board to the wiring harness, providing a reliable electrical connection to help the inverter and compressor receive power. Use it to replace damaged or corroded inverter-to-harness plugs. What it does

• Provides a secure electrical connection between the inverter board and wiring harness
• Restores proper power flow to inverter-driven compressor systems
• Commonly replaced when connectors are cracked, melted, burned, or have corroded pins
• Can eliminate intermittent operation, error codes, or compressor fail-to-start symptoms related to poor connections

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Handle PCB and connector pins carefully to avoid bending pins or introducing debris
• Verify connector orientation and full seating; ensure locking tab engages where present

This small metal pin connects and secures the suspension damper that reduces vibration and movement in your washing machine during the spin cycle. It allows the damper to pivot and absorb shock while keeping the wash basket stable. Replace it if your washer vibrates excessively, makes loud banging noises during spin, or moves around during operation.

Corner bracket for washer structural support. Mounts in frame corner to secure components. Replace if cracked, bent, or broken during installation.

A replacement adjustable leveling leg that supports and stabilizes the appliance and helps restore even height for proper door alignment and stable operation. Use this leg when a worn, bent, missing or damaged leg causes rocking, tilting or uneven gaps. What it does:

• Provides stable support and lets you level the appliance on uneven floors
• Restores correct height so doors close and seal properly
• Stops rocking and reduces vibration caused by a damaged or missing leg
• Compatible with models that use this specific OEM leg design

• Disconnect power and remove or secure contents before adjusting or replacing legs
• Raise and support the appliance safely (use a jack or helper) before removing/installing the leg
• Thread or fasten per the appliance mounting points; tighten securely but avoid over-torquing
• For model-specific fit and installation details

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Self-tapping screw for securing washer components and panels. Replace worn, stripped, or missing screws during repairs or reassembly of your machine.

This electronic control board manages the washer's motor speed and functions, typically located behind the control panel or near the motor. Replace when the washer won't start, stops mid-cycle, or experiences erratic spin speeds and cycle timing.

A small replacement cover that fits over the cabinet shipping screw area to protect the screw and improve the refrigerator's appearance. Installs quickly and restores the factory look where a shipping screw cap is missing. What it does

• Covers and protects the cabinet shipping screw or mounting hole from dirt and snagging
• Restores finished appearance to the appliance exterior where the cap was lost or damaged
• Helps keep the screw area clear of debris that can cause cosmetic or access issues
• Simple snap-in design keeps the cover secured in normal use

• Designed for a snap-in fit over the cabinet shipping screw; no special tools usually required
• Work on a cool, powered-off appliance and follow the manufacturer's safety guidance
• If the fit is tight, use a flat plastic tool or gloved fingers to press the cover into place to avoid scratching
• Only replace with the exact part specified for your appliance location

This is an exterior drain hose catch or retainer that secures the outside portion of the washing machine drain hose. It holds the hose firmly in position to prevent it from disconnecting during the drain cycle. Replace this part if the outer drain hose slips free, causes water leaks on the floor, or if the original catch is cracked or broken.

Rear cabinet cover panel for washers. Encloses the back of the washer cabinet. Replace if cracked, damaged, or missing to restore appearance.

This is an internal drain hose catch that secures the drain hose in place inside the washing machine. It prevents the hose from slipping out of position, ensuring proper water drainage during the wash and spin cycles. Replace this part if the drain hose keeps coming loose, water is not draining properly, or you notice leaks around the drain connection inside the machine.

Replacement power cord for your washer. Connects the machine to your wall outlet. Order a new cord if yours is damaged, frayed, or missing.

Routes wastewater from your washer's drain pump to household plumbing. Replace this external drain hose if cracked, kinked, leaking, or damaged.

Spring-style clamp secures drain hose to pump or fittings, preventing leaks and separation. Replace if loose, corroded, or causing water leaks. Verify fit with your washer model number.

Connects two sections of your washer's drain hose for secure, leak-resistant water discharge. Replace if cracked, loose, or leaking to restore proper fit.

Mounting screw for washer and pedestal installation. Replaces lost, stripped, or damaged screws. Secures components during assembly and repair.

Self-tapping screw for washer control panels, trim, and internal brackets. Replaces missing, stripped, or damaged screws during repairs and maintenance.

Fix slow draining or leaks at the filter access. This washer drain pump filter traps lint and debris before they reach the pump. Easy DIY replacement.

This U-shaped mounting bracket secures and guides the drain hose at the back of the washing machine, keeping it properly positioned during the drain cycle. It prevents the hose from slipping out of the standpipe or laundry tub. Replace this bracket if the drain hose keeps falling out of position, water is spilling during the drain cycle, or the original bracket is cracked or broken.

A small sheet-metal screw used to secure panels and components on compatible GE appliances. Replaces worn or missing fasteners to restore proper fit and stop loose or rattling parts. What it does

• Secures appliance panels, brackets or trim to the cabinet or frame
• Keeps components aligned so doors, panels and controls operate correctly
• Common symptom: loose or rattling panels or trim
• Common symptom: parts that shift or detach during use

• One screw

• Use the correct sized Phillips screwdriver; start threading by hand to avoid cross-threading
• Tighten until snug — avoid over-torquing which can strip threads or crack panels
• Replace only with the same size and thread type for secure fit
• Disconnect power where applicable and follow appliance safety guidance before servicing

M5 x 12 machine screw secures panels, brackets, and internal components in your washer. Replace missing, stripped, or loose screws to restore proper fit.

Quick connector for washer stacking kits. Installs between stacked washer and dryer units. Replace if connector is broken, cracked, or missing.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.