Parts for Ge GTDX185PD0CC: Cabinet & Top Panel Parts

Fixed buzzer that replaces the appliance's audible tone generator in the control panel, restoring beeps and alerts for cycle completion and fault signals. Simple swap that returns audible notifications used during normal operation. What it does:

• Produces the control panel's audible tones for end-of-cycle alerts and warnings.
• Replaces a buzzer that has stopped sounding or produces weak, intermittent, or distorted beeps.
• Helps restore audible error/fault notifications so you can respond to appliance alerts promptly.
• Works as the control panel's dedicated tone generator — pairs with the appliance's existing electronics.

• Disconnect power to the appliance before beginning any service to avoid electrical shock.
• Access the control panel per your model's service instructions and note wire/harness positions before removal.
• Disconnect the buzzer wiring or harness, remove mounting fasteners, and install the replacement in the same orientation.
• Reassemble panels, restore power, and run a test cycle to audible operation.

This is a 10-16 x 1/2 screw used to fasten small appliance components and panels; it restores secure attachment and helps stop rattling or loose parts for reliable operation. What it does:

• Secures panels, brackets, and small assemblies to the appliance
• Prevents movement that can cause noise, vibration or misalignment
• Restores proper fit where a worn or missing screw caused loose parts
• Matches OEM size so replacement fits original mounting points

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread carefully and do not overtighten—stop when snug to avoid damage
• Replace like-for-like; if corrosion or stripped threads are present, repair or replace the mating part as needed

This leveling leg threads into the base of your appliance to provide a stable, adjustable footing. Replacing a worn or missing leg helps keep the cabinet level, reducing vibration and noise for smoother, safer operation.

• Adjusts height so the unit can be leveled on uneven floors
• Maintains solid floor contact to minimize rocking or walking
• Helps reduce vibration and rattling noises during operation
• Signs you need this part: appliance wobbles, sits unevenly, or a foot is missing/damaged

• Disconnect power; for gas units, also shut off the gas supply
• With assistance, carefully tilt or raise the appliance to access the leg
• Unscrew the old leg and thread in the new leg by hand; use a wrench if needed
• Level the unit front-to-back and side-to-side; ensure all legs firmly contact the floor

This silicon controlled rectifier (SCR) controls power flow to heating and motor circuits, restoring proper electronic regulation in appliances that use SCR-based control boards. Replaces a failed SCR to help return normal heat and motor control. What it does:

• Acts as a switch to regulate current to heating elements or motors when the control board signals it.
• Common symptom: unit fails to heat or run when the control board is commanding operation.
• Common symptom: intermittent or no power to specific circuits controlled by the SCR.
• Helps prevent erratic operation when the SCR is functioning properly.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Handle the SCR carefully; avoid bending the stud or damaging terminals.
• Mount and torque stud to specified appliance hardware; ensure good electrical contact and any required heat sink connection.

This replacement screw secures panels, trims, and internal components to restore a snug, rattle-free fit and reliable operation. Use it to replace missing, corroded, or stripped fasteners for safe appliance performance. What it does:

• Fastens cabinet panels, trim pieces, and internal brackets to keep parts aligned and secure
• Replaces missing or damaged screws that cause loose or vibrating panels
• Prevents movement that can lead to wear, noise, or improper sealing
• Matches the original fastener role for appliances that specify part WE2M160

• Disconnect power or unplug the appliance before attempting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Install until snug; avoid overtightening which can strip threads or crack plastic
• If threads are damaged or fastener holes are worn, replace damaged components.

This replacement rear panel and fuse cover protects the appliance's rear electrical area, shielding the fuse assembly and wiring while restoring safe access for service. It fits where the original rear fuse cover is installed. What it does:

• Shields the fuse housing and rear wiring from debris and accidental contact
• Helps prevent damage to the fuse area that can cause intermittent power or electrical faults
• Restores a secure cover when the original is cracked, warped, or missing
• Provides proper access for visual inspection and fuse replacement during service

• Disconnect power (unplug or switch off breaker) before installing.
• Use appropriate screws/fasteners; keep hands clear of sharp sheet-metal edges.
• Align cover over the fuse housing and secure firmly; inspect surrounding wiring before restoring power.

Size: 8-32 t. Includes 12 screws.