Parts for Ge PTD90GBPT1RS: Cabinet & Top Panel Parts

A replacement silicon controlled rectifier (SCR) that restores proper high-current switching for heating or ignition circuits. Replacing a failed SCR helps stop intermittent heating, loss of element power, or erratic control behavior. What it does:

• Switches and regulates high-current power flow to heating, ignition or motor circuits when gated by the appliance control.
• Prevents or causes intermittent/no-heat conditions when failing or shorted.
• Stops erratic cycling or loss of controlled power to the affected circuit.
• Operates as a direct electrical replacement for the factory SCR specified by the appliance manufacturer.

• Disconnect power before servicing; this part is used in high-voltage sections.
• Match part number and orientation exactly; some installations require soldering or secure connector seating.
• Discharge capacitors and observe ESD precautions when handling electronic components.

This factory screw secures dryer panels and internal components, keeping assemblies tight and aligned so the machine operates safely and without vibration or rattling.

• Fastens sheet-metal panels, brackets, or trim to the dryer cabinet/frame
• A loose or missing screw can cause panel vibration, noise, or misalignment
• Helps restore stability after service or when original hardware is lost
• Typical symptoms include rattling, loose panels, or gaps in trim

• Unplug the dryer before servicing
• Keep track of original screw locations and lengths; replace like-for-like
• Start screws by hand to avoid cross-threading, then snug—do not overtighten
• If threads are damaged, inspect mating hole or clip before installing

Size: 8-32 t. Includes 12 screws.

This leveling leg threads into the base of your appliance to provide a stable, adjustable footing. Replacing a worn or missing leg helps keep the cabinet level, reducing vibration and noise for smoother, safer operation.

• Adjusts height so the unit can be leveled on uneven floors
• Maintains solid floor contact to minimize rocking or walking
• Helps reduce vibration and rattling noises during operation
• Signs you need this part: appliance wobbles, sits unevenly, or a foot is missing/damaged

• Disconnect power; for gas units, also shut off the gas supply
• With assistance, carefully tilt or raise the appliance to access the leg
• Unscrew the old leg and thread in the new leg by hand; use a wrench if needed
• Level the unit front-to-back and side-to-side; ensure all legs firmly contact the floor

This top cover is the exterior panel that finishes and protects the appliance's upper interior. It restores a clean appearance and shields wiring and components from dust and accidental contact. What it does:

• Covers and protects internal components at the appliance top to help prevent dust buildup and accidental contact
• Restores the appliance's finished appearance after repair or removal
• Helps support any controls or user-interface components mounted near the top
• Common symptom: visible damage, dents, or missing top panel that expose internal parts

• Always disconnect power (unplug or shut off circuit) before accessing internal parts
• Remove control panel or screws as required to lift off the old cover; retain fasteners for reinstallation
• Handle edges carefully — metal panels may have sharp edges

A genuine replacement mounting screw used to secure appliance panels and trim pieces. Replaces a single worn, stripped or missing fastener to restore proper fit and prevent rattling or loose components. What it does:

• Secures panels, brackets or trim to the appliance frame
• Stops rattling or vibration caused by loose or missing screws
• Restores proper alignment when existing fasteners are stripped or damaged
• Matches OEM fit and thread for reliable fastening

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten — snug until secure to prevent thread damage
• Keep removed hardware organized to ensure correct reassembly

This 120V replacement power cord restores household current to gas ranges and ovens that use a corded connection for clocks, lights, igniters and controls. It provides a straightforward way to replace a damaged or worn cord and regain safe power to the appliance. What it does

• Supplies 120-volt power from the wall outlet to the range/oven's control system, clock and lights.
• Restores ignition and control functions when a frayed or broken cord prevents the appliance from receiving power.
• Replaces cords that show signs of burning, cracking, loose connections, or exposed wiring.
• Reduces risk of electrical faults caused by damaged insulation or terminals.

• One 120V power cord

• Disconnect power at the circuit breaker or unplug the appliance before starting; ensure the appliance is de-energized.
• Route and secure the cord to avoid pinching; tighten terminal screws to manufacturer torque recommendations.

The Water Valve is an OEM part for GE electric dryers. Located near the bottom of the machine, it controls water flow into the condenser system during moisture-sensing cycles.

The moisture sensing function uses this valve to introduce precise amounts of water vapor into the exhaust air stream periodically. This allows the condenser to capture moisture readings accurately and determine optimal cycle time based on humidity levels. 

Causes of failure include mineral buildup restricting flow, worn seals enabling leaks, or misaligned internal components hindering valve movement.

Symptoms of a faulty water valve are: 

• Loss of moisture sensing ability
• Incomplete or improper readings affecting cycle times  
• Water leaks from the valve area
• Failure to inject water vapor as needed

This part is also compatible with some Kenmore models using GE components.