Parts for Briggs & Stratton 40F777-0111-E1: Camshaft, Cylinder, Engine Sump Parts

This oil seal is a genuine OEM replacement part designed for use on a wide variety of small gas-powered appliance engines. Although small, an oil seal is an important part of the oil cylinder assembly as it prevents oil from leaking into other parts of the engine. If oil begins to leak into the engine, it can corrode other parts or even pose a fire hazard. Therefore, it's important that the oil cylinder is tightly sealed to prevent any damage to the engine. Seals can wear out over time, especially if exposed to heat. Heat will cause the seal to shrink, effectively unsealing the oil cylinder. Before making this repair, be sure to drain the oil cylinder of any oil and be prepared for an involved replacement process. This part is compatible with Toro, Murray, and Briggs & Stratton appliances and is sourced from the original manufacturer. It ship individually of other hardware.

Flange screws have a flange located near the top of the screw, which helps to distribute the connection force over a larger area to reduce potential damage to the machine. It also allows the screws to be used in oversized or irregular holes, and it helps to ensure they stay in place. This flange screw also has a hex top. Screws can last for a long time. However, they may become corroded or worn over time and need to be replaced. They could also become lost and need a replacement. Without all of the screws in the proper places in a machine, it could vibrate too much, which could render it less effective or unsafe to use. The flange screw is a genuine OEM part that can be used with many types of machines including lawn mowers, snowblowers, tillers, pressure washers, leaf blowers, generators, wood chippers, and other small engines. The screws are compatible with Briggs & Stratton, Craftsman, Toro, Cub Cadet, Murray, Lawn-Boy, Snapper, Simplicity, and MTD.

This replacement oil drain plug is a genuine OEM part for a lawn tractor or generator engine. The oil drain plug connects to the base of the oil tank and allows the appliance owner to drain used oil and replace it with new, clean oil. The oil drain plug is threaded to screw into the oil tank and prevent it from popping out of place while the appliance is in use. The most likely reason to replace an oil drain plug is if the old plug's threading has become stripped and no longer holds onto the oil tank. Alternatively, the plug is quite small and could easily be misplaced during an oil change. If lost, oil will leak from the engine, causing parts to overheat. Fortunately, replacing a lost or damaged oil drain plug is simple and only requires screwing a new plug into place. This replacement plug is a high-quality part that fits Craftsman and Murray products. It comes sourced from its original manufacturer and ships individually, without any additional hardware.

The oil seal plays an important role in protecting the oil as it flows into the crankshaft and engine block. It creates a strong seal and ensures that the oil can flow effectively into the engine for proper operation. Over time, rubber seals degrade and wear out, so their replacement will be a part of routine maintenance. If there are oil leaks around the crankshaft or engine, this seal may be the culprit. Replacing the oil seal will ensure proper oil pressure and avoid oil leaks that could lead to more serious damage. When installing this replacement part, it is important to use a rubber mallet or large socket to tap the part into place. This is a genuine Briggs & Stratton part that is a replacement for various compatible small engines. It can fit select engines on Toro, Husqvarna, and Briggs & Stratton equipment. This oil seal is sold individually and compatible with a variety of engines. This OEM replacement is made of durable rubber and sold individually.

This is a durable metal valve tappet that is designed for use in small motor lawn equipment. It is attached to the push rod. The valve tappet takes the rotating motion from the camshaft and turns it into a linear motion for the valves to operate correctly. In some cases, the valve tappet can become damaged or break and will need to be replaced.If there is an issue with the valve tappet, a set of pliers will be needed to make the replacement. For safety, use work gloves and make sure the spark plug wire is disconnected before starting the replacement. The crankcase breather, muffler, and other components will need to be taken off to gain access to the valve tappet to replace it.This valve tappet is a genuine OEM replacement component directly sourced from the manufacturer. It is sold as an individual replacement part. It is designed to be used on lawnmowers, snowblowers, tillers, pressure washers, leaf blowers, generators, and chipper shredders manufactured by Briggs & Stratton, Toro, Cub Cadet, Lawn-Boy, Snapper, MTD, and Simplicity.

This part is a replacement camshaft. This is a genuine OEM part made by Midwest Engine and has been sourced directly from the manufacturer. It is intended to replace a defective or broken camshaft in various models of lawn tractors.The camshaft closes and opens the equipment's exhaust and intake valves. This part is driven by the crankshaft gear and will need to be immediately replaced if bent, dented, or otherwise broken in any way. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to use this battery, the appropriate owner's manual and equipment diagrams should be referred to. This battery is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with lawn tractor models that have been manufactured by Midwest Engine, Briggs and Stratton, and other brands.

This oil pump cover is a genuine Midwest Engine part, sold individually. This oil pump cover can be used as a replacement part for lawnmowers, snowblowers, wood chippers, and lawn tractors. It ensures that the oil pump can deliver oil to the engine without any excessive oil leakage. Symptoms of a damaged oil pump cover can include oil leakage in and around the cover, reduced oil pressure, and oil leakage in and around the intake manifold gasket. If any of these symptoms occur and are directly attributable to the oil pump cover, the part should be immediately replaced with this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This Oil pump cover is compatible with the following outdoor appliance brands: Midwest Engine, Briggs & Stratton, Toro, Simplicity, Cub Cadet, Lawn-Boy, and MTD.

The oil filter strains the oil as it runs through the machine, helping to remove debris and buildup to ensure that only the purest oil gets into the engine. Over time, oil gets dirty, and therefore so will the filter. This could lead to clogs and will eventually require replacement. Typically, oil filters are replaced as a part of routine oil changes, but there are some instances where an emergency replacement may be required. Replacing a clogged oil filter could improve the performance of the equipment and help reduce your emissions. To replace the oil filter, drain all of the oil from the engine and use an oil filter wrench to remove the old filter and screw the new one in place. Once the filter is secured, refill the oil and get back to using the equipment at the optimal operating performance. This Briggs & Stratton oil filter offers compatibility with a number of its lawn equipment engines. All genuine parts from this brand are designed to provide optimal performance and adhere to emissions guidelines. Be sure to check your user manual for fit and model compatibility.

Oil filter for most Intek and Vanguard engines and selected L-head twin cylinder engines. It is recommended to replace the oil filter at least once per season.