Parts for Ge CFCP1RKBA SS: 09 - Case Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Secures the hinge cover to your refrigerator door or cabinet hinge. Replace this screw if it's missing, stripped, or damaged to stop the cover from loosening.

Covers the base of your refrigerator beneath the door. Replace if cracked, broken, discolored, or missing to restore appearance and protect components.

Replacement mounting screw for refrigerator brackets, panels, and handles. Restores secure fit when original fastener is missing, stripped, or damaged.

White plastic clip that secures the rear of refrigerator shelves or drawer rails to the cabinet wall. Replace if cracked, broken, or missing.

This is a silicon controlled rectifier (SCR) used in appliance control circuits to regulate power to heaters or motors, helping the appliance deliver consistent operation and heat when needed. What it does:

• Acts as a switch in the control circuit to regulate current flow to heating elements or motors
• Can prevent or allow power to the load based on control signals from the appliance module
• Common symptom indicators: intermittent or no heat, unit won't reach operating temperature, or inconsistent operation of the controlled component
• Used where precise control of AC power is required for safe, efficient performance

• One silicon controlled rectifier (SCR) as described

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle the part carefully; avoid bending terminals and observe anti-static precautions
• Verify wiring and terminal orientation matches the original before reconnecting

Fix inconsistent cooling or excess moisture in your refrigerator with this humidity sensor. Direct replacement part restores proper climate control.

Protective housing cover for refrigerator humidity sensor. Replaces cracked, broken, or missing covers. Installs in fresh food compartment.

Fix inconsistent cooling or frost buildup with this refrigerator humidity sensor. Monitors moisture levels to optimize defrost cycles. Direct replacement.

Adjustable hinge pin that installs in the door hinge bracket to provide a pivot point. Replace when worn, loose, or damaged to restore door alignment.

Replacement closure spring for refrigerator doors and panels. Installs at hinge points to provide smooth closing action. Needed when original is broken, stretched, or missing.

This replacement corner cap restores the finished edge and protective cover on an oven door corner for a clean appearance and proper fit. It replaces a cracked, chipped, or missing corner that can catch debris or show damage. What it does:

• Covers and protects the outer corner of the oven door from chips and dents
• Helps maintain a smooth door edge so the door closes and seals properly
• Improves cosmetic appearance when the original corner is cracked or worn
• Reduces sharp or rough edges that can catch on clothing or cause minor cuts

• Turn off power to the appliance and allow the oven to cool before servicing
• Installation may require partially removing the oven door or trim; have basic hand tools ready
• Handle the door and trim carefully to avoid scratching finished surfaces

Front roller assembly for refrigerators. Mounts to the base to enable smooth movement and leveling. Replace if cracked, worn, or mobility is impaired.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

Adjustable leveling leg installs at the base of your refrigerator to restore proper height and stability. Replace worn, damaged, or missing legs.

Leg bracket assembly for refrigerators. Mounts to the base to secure and support adjustable legs. Replace if cracked, bent, or broken to restore stability.

The GE Door Light Switch is an OEM Replacement Part that serves as the Freezer Door Fan and Light Switch. The switch is made from metal, wiring, and plastic. It plays an essential role in energy conservation by turning off the light when the refrigerator or freezer door is closed

Over time, the door light switch can wear out or fail due to frequent use, exposure to moisture, or electrical issues. When this happens, the interior light may not function correctly, which can hinder visibility inside the refrigerator.

Symptoms of a bad door light switch may include:

• Interior light not turning on when the door is opened
• Interior light not turning off when the door is closed
• Flickering or intermittent operation of the interior light

This switch is compatible with select GE and Hotpoint models.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

Replacement door hinge closure for your refrigerator. Installs on the door frame to secure the hinge assembly. Needed when original is cracked or broken.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.