Parts for Ge GBSC0HCXCRBB: 06 - Case Parts

8-18 CA HX 1/2 S

Covers and protects the lower front of your refrigerator. Replace if cracked, broken, or missing to maintain a finished look and proper airflow routing.

Bottom hinge pin for refrigerator doors. Connects door to cabinet frame for smooth opening and closing. Replace if worn, damaged, or missing.

Secures the door hinge pin and keeps the refrigerator door aligned. Replace if cracked, broken, or missing to prevent door sag and uneven gaps.

Hex head screw for securing refrigerator components and panels. Replace if screw is stripped, corroded, or missing during repairs or reassembly.

This is a silicon controlled rectifier (SCR) used in appliance control circuits to regulate power to heaters or motors, helping the appliance deliver consistent operation and heat when needed. What it does:

• Acts as a switch in the control circuit to regulate current flow to heating elements or motors
• Can prevent or allow power to the load based on control signals from the appliance module
• Common symptom indicators: intermittent or no heat, unit won't reach operating temperature, or inconsistent operation of the controlled component
• Used where precise control of AC power is required for safe, efficient performance

• One silicon controlled rectifier (SCR) as described

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle the part carefully; avoid bending terminals and observe anti-static precautions
• Verify wiring and terminal orientation matches the original before reconnecting

This is a replacement cover mullion screw that secures the mullion/trim cover on the refrigerator door assembly, restoring a snug, rattle-free fit and keeping the trim properly aligned. What it does

• Secures the mullion or center trim cover to the refrigerator door
• Prevents the trim from vibrating or coming loose during door use
• Addresses symptoms like a loose or rattling mullion cover
• Restores proper trim alignment for a finished appearance

• One cover mullion screw

• High-level hand tools (screwdriver) are typically all that's needed
• Tighten until snug; avoid overtightening to prevent striping the hole or damaging trim
• Disconnect power only if removal of other parts requires working near electrical components; otherwise, ensure doors are stable before working

White plastic cover cap that conceals hinge screws on your refrigerator door. Replaces worn, cracked, or missing covers for a clean finished look.

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.

White corner cap cover for side-by-side refrigerators. Replaces cracked, broken, or missing corner trim pieces. Restores clean appearance.

This replacement corner cap restores the finished edge and protective cover on an oven door corner for a clean appearance and proper fit. It replaces a cracked, chipped, or missing corner that can catch debris or show damage. What it does:

• Covers and protects the outer corner of the oven door from chips and dents
• Helps maintain a smooth door edge so the door closes and seals properly
• Improves cosmetic appearance when the original corner is cracked or worn
• Reduces sharp or rough edges that can catch on clothing or cause minor cuts

• Turn off power to the appliance and allow the oven to cool before servicing
• Installation may require partially removing the oven door or trim; have basic hand tools ready
• Handle the door and trim carefully to avoid scratching finished surfaces

Machine screw secures panels, brackets, and components in refrigerators. Replaces lost, stripped, or damaged 10-32 fasteners to restore stability.

Air separator divider for side-by-side refrigerators. Replaces cracked, broken, or missing air flow dividers in the fresh food compartment.

Threads into the leveling leg or adjuster bracket to raise or lower your refrigerator cabinet. Replace if stripped, missing, or worn for stable footing.

Leg bracket assembly for refrigerators. Mounts to the base to secure and support adjustable legs. Replace if cracked, bent, or broken to restore stability.

Bottom door hinge assembly for refrigerators. Mounts at the base of the door to provide smooth opening and closing. Replace if cracked or broken.

Replace your refrigerator's hinge cover if cracked, broken, or missing. This plastic cap installs over the door hinge mechanism for a finished look.

Covers and protects the top door hinge assembly on your refrigerator. Replace this plastic cover if it's cracked, broken, or missing to restore a clean finish.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.