Parts for Ge GDSC3KCXABB: 06 - Case Parts

8-18 CA HX 1/2 S

Base grille panel that covers the area below the refrigerator door. Replace if cracked, broken, or missing to restore the finished appearance.

Base grille for refrigerators. Installs at bottom front of unit. Replace if cracked, broken, discolored, or missing to restore finished appearance.

Secures the door hinge pin and keeps the refrigerator door aligned. Replace if cracked, broken, or missing to prevent door sag and uneven gaps.

Hex head screw for securing refrigerator components and panels. Replace if screw is stripped, corroded, or missing during repairs or reassembly.

This is a silicon controlled rectifier (SCR) used in appliance control circuits to regulate power to heaters or motors, helping the appliance deliver consistent operation and heat when needed. What it does:

• Acts as a switch in the control circui

This is a replacement cover mullion screw that secures the mullion/trim cover on the refrigerator door assembly, restoring a snug, rattle-free fit and keeping the trim properly aligned. What it does

• Secures the mullion or center trim cover to the refrigerator door
• Prevents the trim from vibrating or coming loose during door use
• Addresses symptoms like a loose or rattling mullion cover
• Restores proper trim alignment for a finished appearance

• One cover mullion screw

• High-level hand tools (screwdriver) are typically all that's needed
• Tighten until snug; avoid overtightening to prevent striping the hole or damaging trim
• Disconnect power only if removal of other parts requires working near electrical components; otherwise, ensure doors are stable before working

White plastic cover cap that conceals hinge screws on your refrigerator door. Replaces worn, cracked, or missing covers for a clean finished look.

This plug cover is a small protective cap that shields an appliance's power or wiring plug/terminal area from dust and accidental contact. It helps keep connections clean and reduces the risk of debris buildup. What it does

• Covers and protects an exposed appliance plug or terminal connection
• Helps prevent dust, dirt and small debris from entering the plug area
• Reduces risk of accidental contact with terminals while appliance is serviced or idle
• Commonly used when a cord or plug is not in use or during maintenance

• No special tools required; push the cover firmly into place over the plug or terminal
• Ensure the appliance is powered off and unplugged before servicing nearby components
• Inspect the cover for damage and replace if cracked or deformed
• Not intended to alter electrical connections or provide waterproofing; use only as a protective cap

Replacement plug cover for your refrigerator. Installs over plug openings to provide a finished look. Order when original is cracked, broken, or missing.

White corner cap cover for side-by-side refrigerators. Replaces cracked, broken, or missing corner trim pieces. Restores clean appearance.

This replacement corner cap restores the finished edge and protective cover on an oven door corner for a clean appearance and proper fit. It replaces a cracked, chipped, or missing corner that can catch debris or show damage. What it does:

• Cover

Machine screw secures panels, brackets, and components in refrigerators. Replaces lost, stripped, or damaged 10-32 fasteners to restore stability.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Air separator divider for side-by-side refrigerators. Replaces cracked, broken, or missing air flow dividers in the fresh food compartment.

Threads into the leveling leg or adjuster bracket to raise or lower your refrigerator cabinet. Replace if stripped, missing, or worn for stable footing.

Leg bracket assembly that mounts to the bottom of your refrigerator to support and secure the leveling legs. Replace if cracked, broken, or missing.

Lever arm closure component for refrigerator freezer drawers. Mounts in base channel and works with cam to auto-close drawer. Replace if broken or missing.

Freezer door closure lever arm for refrigerators. Mounts inside the freezer compartment to control door closing mechanism. Replace if broken or worn.

Replacement lever arm for refrigerator freezer door closure mechanism. Installs on door hinge assembly. Needed when original is broken or worn.

Freezer door closure lever arm for refrigerators. Installs inside the freezer compartment to activate door sealing. Replace if cracked or broken.

Covers and protects the top door hinge assembly on your refrigerator. Replace this plastic cover if it's cracked, broken, or missing to restore a clean finish.

Replace your refrigerator's hinge cover if cracked, broken, or missing. This plastic cap installs over the door hinge mechanism for a finished look.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.