Parts for Bosch HBN755AUC/02: Cavity 2 Parts

This is a glass panel that mounts on the front fascia of a wall oven, typically covering the lower cavity area. It serves as both a decorative and protective element on the oven's front face. Replace this panel if it is cracked, chipped, or shattered.

M4.2 x 9.5mm mounting screw for wall ovens. Secures interior panels, brackets, and components. Replace if stripped, missing, or damaged during repairs.

This outer cover protects and secures the catalyzer element, keeping it in position and shielding it from debris and contact damage. It helps maintain safe operation by preventing movement and minimizing noise from a loose element. What it does

• Protects the catalyzer element from physical damage and foreign debris
• Holds the catalyzer element securely in its mounting location
• Reduces vibration and rattling that can occur with a loose or damaged cover
• Helps maintain correct airflow/clearance around the catalyzer element

• Disconnect power (and gas supply where applicable) before beginning work
• Handle the part carefully to avoid bending or cracking the cover
• Reuse original fasteners only if undamaged; otherwise replace with OEM-specified hardware

Seals oven door to prevent heat loss and maintain cooking temperatures. Replace if cracked, torn, or no longer creating a tight seal. Verify fit with your model.

This rear panel is the oven back cover that protects internal components and helps maintain proper ventilation. It replaces damaged or missing back panels to restore a finished exterior and shielding for electronics. What it does

• Covers and protects the oven's internal wiring, heating elements, and components from debris and accidental contact
• Helps direct ventilation and air flow from the oven cavity to the exhaust/chassis openings
• Stops drafts and reduces dust entry that can cause component issues or noise
• Common symptom: bent, rusted, punctured, or missing back panel; visible gaps, rattling, or unusual odors

• One rear panel

• Disconnect power to the appliance before starting any repair
• Use proper tools; panel may be secured with screws and attached to sheet-metal edges
• Panels can have sharp edges—wear gloves and eye protection
• Removing/installing may require pulling the appliance away from cabinetry; check your model's service manual for model-specific disassembly steps

Replacement spacer for wall ovens. Maintains proper alignment and spacing between oven components. Order a new spacer if yours is cracked or missing.

This genuine right rail support secures the dishwasher rack slide and keeps the lower rack aligned for smooth movement and stable loading. It replaces a missing or damaged support to restore proper rack tracking and reduce wobble. What it does:

• Supports the right side rack rail so the lower rack slides straight and evenly
• Prevents rack misalignment, catching, or wobbling during insertion and removal
• Replaces cracked, broken, or missing plastic support pieces that let the rack sag
• Works with the existing rail and rollers to restore normal rack motion

• One right rail support (black), as shown

• Disconnect power to the appliance before starting any repair
• Remove the lower rack to access the rail support; common hand tools may be required
• Inspect rails and rollers for damage and replace any worn components for best results
• Handle plastic parts carefully to avoid cracking during installation

This grille for pan is a replacement trim piece that restores proper airflow and appearance around the appliance pan. It helps keep the pan area protected and looking finished after repair. What it does:

• Covers and ventilates the pan opening to help direct airflow and prevent debris entry
• Replaces a cracked, warped, or missing grille to restore fit and finish
• Helps eliminate rattling or rubbing caused by a damaged trim piece
• Matches OEM fit so it installs cleanly with the original mounting points

• Install requires removal of the surrounding trim or access panel; follow your appliance manual
• Handle carefully to avoid scratching the finish; use non-marring tools as needed
• Disconnect power to the appliance before working in the service area
• Replace damaged clips or screws with OEM fasteners for secure fit

Replacement rack shelf for your wall oven. Installs inside the oven cavity to hold cookware. Order a new shelf if yours is warped, damaged, or missing.