Parts for Ge AJK06LHV1: 02 - Section2 Parts

AC won't turn on or off? The main switch controls power to your air conditioner. Common repair for units that won't start or respond to controls.

Traps dust and lint to maintain airflow and cooling performance in room air conditioners. Replace when damaged or missing to protect the evaporator coil.

This replacement knob assembly restores tactile control for a range or oven control shaft so you can select cook settings easily and safely. It replaces a cracked, loose, or missing control knob to regain reliable adjustment. What it does:

• Fits onto the range/oven control shaft to set burner or oven temperature and functions
• Replaces knobs that are cracked, stripped, loose, or difficult to turn
• Helps restore accurate user input for heating and timer selections
• Works with standard splined control shafts used on many GE ranges

• Disconnect power (and gas supply if applicable) before starting any work
• Pull off the old knob; align splines and push the replacement knob straight onto the control shaft
• If knob is stiff after installation, remove and re-seat to ensure proper spline engagement
• If mounting hardware, trim, or control shaft is damaged, replace those parts as needed for a secure fit

Secures louvers in your air conditioner. Replace if louvers are loose, rattling, or won't stay in position. Verify fit with your model number.

Restricted airflow or overheating? This rear grille protects the condenser and fan while ensuring proper ventilation. Installs with clips and screws.

Rubber grommet that secures the front grille to your air conditioner cabinet. Replace if cracked, missing, or no longer holding the grille firmly in place.

This cover for the drip tray replaces a cracked or missing surface that directs condensate and defrost water into the drain channel, helping keep the cabinet floor dry and the drain path clear. What it does:

• Covers and channels condensate/defrost water toward the drain to prevent pooling under the tray
• Restores proper fit where the original cover is cracked, warped, or missing
• Helps reduce water leaks and standing moisture that can cause odors or floor damage
• Visible, inexpensive part often replaced when water is observed under the fridge or ice/water systems

• One cover, drip tray

• Disconnect power to the appliance before beginning any service
• Remove any access panels or shelves blocking the drip tray to reach the cover
• Inspect surrounding drain components for clogs or damage while replacing the cover
• Handle trimmed plastic edges carefully; hand-tighten fasteners to avoid cracking the new cover

This replacement barrier snaps into a refrigerator shelf or bin to help keep items from sliding forward and falling. It restores the shelf edge/retainer function so stored items stay organized and contained. What it does:

• Acts as a shelf/basket retainer to keep food and containers from shifting or falling
• Replaces broken, cracked or missing plastic shelf barriers that allow items to slide forward
• Helps maintain an organized shelf edge or deli/drawer area
• Fits into existing shelf/bin slots and holds items in place during door use or drawer movement

• One replacement barrier

• Remove food and any loose items from the shelf or bin before starting
• Align the barrier with the shelf/bin slots and press until it snaps or seats securely
• No special tools usually required; use a flat tool only if needed to help seat or remove the old piece

This mounting bracket secures internal appliance components to their chassis, restoring proper alignment and reducing movement. It's a simple replacement that helps stop rattles and keeps parts seated for reliable operation. What it does

• Provides a stable mounting point for internal panels or assemblies, preventing vibration and noise
• Restores proper alignment when a bent or broken bracket allows components to sag or shift
• Helps eliminate rattling or knocking sounds caused by loose or missing hardware
• Supports safe, secure attachment so other parts can function without strain

• One mounting bracket

• Disconnect power (and water, if applicable) before servicing to avoid shock or injury
• Basic hand tools (screwdriver, nut driver) are typically required; keep removed fasteners for re-use if undamaged
• Inspect surrounding parts and mounting points; replace any stripped screws or damaged anchors
• Tighten hardware securely but avoid over-torquing which can strip threads or crack plastic