Chore Performer

Log splitter not building pressure or splitting slowly? This hydraulic gear pump restores splitting force. Moderate difficulty repair for experienced DIYers.

Fix sluggish or inconsistent splitting action with this log splitter control valve. Regulates hydraulic cylinder movement for smooth operation.

Transfers torque between shafts in your log splitter. Replace when you notice excessive vibration, noise, or reduced splitting power. Verify fit with your model number.

Replacement gasket for tillers that seals components to prevent leaks. Replace if worn, cracked, or causing fluid leaks. Verify fit with your model number.

Seal for gas snowblowers, tillers, and chore performers. Prevents air leaks to maintain proper operation. Replace if damaged or worn. Verify fit with your model.

Steering ball joint assembly for lawn tractors and snowblowers. Secures drag links and tie rod ends. Replace if worn, cracked, or loose for safe operation.

This is a simple set of lawnmower ignition keys. They’re also used for an array of riding mowers, lawn tractors, and even snowblowers. To simplify repair and replacement procedures, most manufacturers use standardized keys for all their machines in a given class. As a result, a single key can be used for dozens of machines. The keys are manufactured from stainless steel, with an INDAK logo stamped into the center. Regardless of whether the machine is a walk-behind mower or a full-sized lawn tractor, a keyed ignition is easier to operate than a recoil cord. Similarly, replacing a key is generally straightforward. The exception is if the old key has snapped off in the ignition. In this case, a set of needle-nosed pliers can sometimes be used to extract the key. A powerful magnet can also be helpful if the broken key is being stubborn. In the worst-case scenario, the ignition may need to be replaced. This is an OEM part sourced directly from MTD, and it is sold as a set of two.

This replacement part is a switch cover and is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This switch cover is meant to protect the user from parts that can be dangerous. A new switch cover might be needed if the current one is missing or damaged. Though this part is small, it is very important and should be replaced if needed. This should be a simple repair and will only take a few minutes. work gloves are recommended if the previous part is damaged. Be sure the engine is powered down before replacing this part to ensure safety to the user and those in the vicinity. This switch cover is sold as a single part and is sourced directly from the manufacturer to ensure a proper fit in different appliances. This part is a genuine OEM replacement part.

This is a snap mount safety switch that is a part of many types of lawn and garden equipment. The safety switch is made of plastic and has a metal four-pronged plug on the bottom. A button is located on the top. Inside of the base, there are two sets of contacts. One set is used to create a circuit between two blades, while the other set makes the circuit for the other pair of blades. One set is grounded and the other connects to the engine of the tool.Replacing the safety switch is required if it is no longer working or has been damaged. Turn off the tool, allow it to cool, and disconnect the spark plug wire. Remove the engine cover before taking off the fuel tank assembly. The engine blower housing will also need to be removed. Access the snap mount safety switch and take it out of the tool before attaching a new switch.This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual part. The snap mount safety switch is designed to be used with wood chippers, leaf blowers, and lawnmowers manufactured by Craftsman, Yard Machines, Cub Cadet, Yard-Man, and MTD.

This part is a replacement push nut. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or detached push nut in snow blowers.Push nuts are a special type of fastener that secures together different equipment components. Push nuts will need to be replaced if worn, broken, lost, or otherwise ineffective. When working on or near an engine, it's important to make sure the equipment is powered off and completely cool before starting any repairs. For more accurate information on how and where to install this push nut, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality materials. This push nut can be used with different models of snow blowers that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Part sold individually.

Push nut for lawn mowers and tractors. Secures components in place. Replace if missing, damaged, or no longer holding parts firmly during operation.

King pin bearing for lawn tractors and riding mowers. Replace if steering feels loose or rough. Verify fit using your equipment's model number.

Protective dust cap for tiller engines and mechanisms. Replaces cracked, broken, or missing caps that expose internal components to dirt and debris.

Extension spring for lawn tractors and snow blowers. Installs on deck, transmission, or control linkage. Replace if stretched, broken, or missing.

Compression spring for lawn mowers and outdoor power equipment. Replaces broken, worn, or missing springs. Essential hardware for proper operation.

Replacement torsion spring for chipper shredders. Restores proper tension and function. Needed when original spring is broken, worn, or missing.