Chore Performer

Replacement spacer for log splitter assemblies. Maintains proper alignment and spacing between components. Order if your original is missing or damaged.

This drive belt is made for use on lawn mowers produced by multiple manufacturers. This belt attached the motor to the blade. This causes the driveshaft to rotate the blade. Because these belts are made of rubber, normal wear tear causes deterioration over time.Deterioration can take the form of cracking, tearing, or stretching of the drive belt. This can cause a complete breakdown of the lawn mower or reduced performance. If the mower is acting sluggish, it may be time to check the belt and replace it if necessary.Before removing and replacing the belt, it is important to drain the fuel tank and remove the spark plugs to ensure safety. Always disengage the blades and wear gloves when replacing the drive belt. After removing the damaged belt, slide the new belt on and reinstall the spark plug before operating the mower.This drive belt is OEM sourced. It is an individual part designed for use with edgers made by Troy-Bilt, Yard-Man, Yard Machines, Cub Cadet, and MTD.

This replacement part is a suction hose. It is a genuine replacement part made by MTD. A suction hose allows the air in water inside the machine to be filtered out through the hose. This allows the machine to continue running and is essential to the overall operation of the appliance.A new suction hose might be needed if the current one is damaged or missing. The user might notice that there are leaks among the hose, and if this is the case, it should be replaced as soon as possible. Be sure the engine is powered completely down before attempting this repair. This part is sold as a single piece and can be used in many different appliances. THis is a genuine OEM replacement part and is sourced directly from the manufacturer. This ensures proper use and long-lasting results.

Hex screw fastener for lawn tractors and outdoor power equipment. Secures components throughout the machine. Replace if stripped, overtightened, or missing.

Replacement carriage bolt for lawn mowers and tillers. Secures components to frame and housing. Replace when bolt is stripped, missing, or damaged.

Hex nut for securing components on outdoor power equipment. Replace when threads are stripped, nut is corroded, or hardware is missing or damaged.

Suction hose for log splitters. Replace if cracked, leaking, or causing hydraulic performance issues. Verify fit with your model number before ordering.

This is a vinyl-plastic grip that slides over the handle bar of a snowblower. It provides a comfortable, non-slip surface for controlling the machine during operation. Replace this grip if it has become cracked, torn, or too loose to stay securely on the handle.

Replacement discharge chute for chipper shredders. Directs wood chips and debris away from machine and operator. Replace if cracked, broken, or missing.

This genuine OEM part is a compression spring for a lawnmower. The compression spring is the spring that holds the mower deck onto the lawnmower. Over time, the compression spring can become degraded due to excessive wear and tear. If it is no longer securing the mower deck, it will need to be replaced. Luckily, replacing this part is a relatively simple process.To replace the spring, make sure the mower deck is set to the lowest position. Locate the old retainer spring and pull it out and away from the mower. Once removed, slide the new spring into its proper position. Make sure it fits tightly, and the mower deck is secured. Once secured, power the mower to see if the spring stays in place during operation. If it does, then the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

Small metal washer that installs with screws and bolts throughout lawn mowers and outdoor power equipment. Replace if cracked, worn, or missing.

This is a genuine replacement OEM throttle control cable. The throttle control cable is comprised of an internal wire that slides through the external housing. Force is transferred from the accelerator pedal to the control linkage mounted to the throttle body from this sliding movement. If constant speed is not being maintained from the cruise control or delays starting, stopping, or jerking, then it may be time to replace the throttle control. To replace the throttle control a pair of pliers is needed. Remove the cable housing using pliers. The housings will swivel off the base and slide down the cable. Next, thread the cable wire through the housing. Locate the wire base on the back of the engine and run the cable through the throttle base and throttle arm. With the throttle all the way down, slide the cable through the housing and into the handle unit to attach it to the throttle handle. Pull the cable with a pair of pliers to make it tight and turn the lock screw. Replace the throttle to test the tension. If the mower, edger, or trimmer is running too high then loosen the cable.This throttle control works with lawn mowers, edgers, and trimmers. This is an OEM part sourced directly from the manufacturer and sold individually.

This is a control cable designed for use with a string trimmer. The cable transmits operator input from the handle to the engine or cutting head, typically controlling throttle or engagement functions. Replace this cable if the trimmer does not respond to handle controls, the cable is frayed, kinked, or broken, or if the trimmer head fails to engage or disengage properly.