Clicklink Trimmer

The cam is a part used in trimmers to counterbalance the blades. This is a small, 1 x 1 inch, circular part with a small cutout in it. When a trimmer is used on a regular basis, it will cause wear and tear to the cams. Over time, these parts can fail and will need to be replaced to ensure the trimmer is working and cutting properly. This is an OEM part sourced directly from the manufacturer. It is sold individually.The cams in a trimmer are mounted on one side of a drive member with the axis of the two cams lying on the opposite sides of the axis of the drive member. The axis of one cam should be spaced further away from the axis of the other cam. This cam engages a cutting blade of lower mass and then the other blade in order to counterbalance the inertial forces created by the reciprocating cutting blades.There are several manufacturers of this part. These include Craftsman, ClickLink, Trimmer Plus, MTD, and Cub Cadet. This replacement part is compatible with hedge trimmers and string trimmers. Remember to always wear protective gear, such as work gloves and eye protection, when operating this type of machinery.

This oil line is a genuine MTD part, sold individually. This oil line can be used as a replacement part in a pole saw. The purpose of the oil line in a pole saw is to provide a safe and guided passageway through which oil can channel into the appliance when the appliance is low on oil and requires additional fuel in order to continue its standard use.The oil line in a pole saw might be damaged at any point within its typical lifespan. If this damage occurs to the extent that the oil line is compromised and oil cannot be safely passed into the oil tank in order for the appliance to consume the oil at regular intervals, the oil line might have to be completely removed and replaced by this genuine OEM replacement part as soon as possible.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This oil line is compatible with the following outdoor appliance brands: MTD, Troy-Bilt, and Cub Cadet.

The part listed is an MTD upper boom assembly. An upper boom assembly is manufactured for installation on various brands of string trimmers. The boom assembly is made up of the upper and lower assemblies, respectively. The purpose of the upper boom assembly on a string trimmer is to help power the trimmer head. Essentially, the boom assembly acts as the driveshaft of the string trimmer. The boom assembly can also be unlocked and extended, allowing the string trimmer to reach further distances or heightened elevations. When the boom assembly becomes damaged, the string trimmer may not function as a working unit. There is a possibility the machine still powers but still has issues with the trimmer head. To install, remove the handle assembly of the string trimmer. There are several screws and an anti-rotation screw that make up this assembly. Remove the trigger and trigger springs, and pull the handle assembly away from the throttle cable. Remove the anti-rotation screw from the shaft of the trimmer and loosen the clamp. This should allow the shaft to be separated from the motor. Repeat these steps in reverse to install the new boom assembly.This product is a genuine OEM part sourced directly from MTD. This product is compatible with MTD, Troy Bilt, RoboMow, and Remington trimmers.

This blade guard is a genuine MTD part, sold individually. This blade guard can be used as a replacement part for a string trimmer. This blade guard protects the blades of the string trimmer so that they are not damaged upon impact with the surface on which the string trimmer is being operated.The blade guard might have to be replaced at some point within the standard lifespan of the appliance in the event that the component suffers damage. This could occur if the blade guard is chipped, torn, punctured, or sufficiently eroded to the point that the blades are directly exposed to potential impact with hard surfaces. The blade guard needs to be removed and replaced with this genuine OEM replacement part if the blades are exposed or are at risk of exposure over general long-term usage.This is an OEM part sourced directly from the manufacturer. It is sold individually. This blade guard is compatible with the following brands: MTD, Craftsman, and Cub Cadet.

This deflector is a genuine MTD part. It is designed to be a replacement part on certain makes and models of string trimmers and handhelds.On string trimmers, the deflector protects the user while the trimmer is in use from flying debris. Because it frequently comes into contact with debris, it is very common for it to break or become damaged through routine use. It is an important safety feature so it must be replaced before it is used again.This deflector is a genuine OEM part sourced directly from the manufacturer. It is sold individually, though it does come with the hardware necessary to replace it. It is compatible with machines made by ClickLink, Craftsman, Cub Cadet, MTD, and Trimmer Plus.

This replacement part is a drive shaft housing and is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This drive shaft housing is found in trimmers and edgers and is the main part that connects the user controls to the bottom part of the trimmer. This part is important as it allows the user to control the power and settings of the trimmer from a standing position. A new drive shaft housing might be needed if the current one is damaged. The long pole that connects the user controls and the blade is the most important part of the trimmer and if it is damaged, the entire appliance may be unable to be used. Be sure to wear work gloves especially if the old drive shaft is damaged. The user might need to handle the blade so be careful of injury. This is an OEM This part is sold individually.