Parts for Kitchenaid 5KSM7590ZER0: 01 - Color Variation Parts

This porcelain enamel finish restores the factory color and smooth, glossy surface to compatible ranges and cooktops, improving appearance and protecting underlying metal from wear and staining. What it does

• Replaces worn, chipped, or faded enamel finish to make the appliance look like new
• Provides a durable, heat-resistant surface that resists stains and everyday wear
• Matches the OEM "Empire Red" color for a cohesive, factory-correct appearance
• Helps protect the underlying metal from corrosion and further cosmetic damage

• One porcelain enamel finish (Empire Red)

• Disconnect power and gas before starting any repair
• Removal of trim, screws, or panels may be required; follow the appliance's OEM service instructions
• Handle with care to avoid chipping the enamel during installation

This motor housing is the outer mounting and protective enclosure for the appliance motor, finished in white to match the cabinet. It provides a secure support for the motor and helps isolate noise and vibration. What it does:

• Supports and secures the motor assembly in the appliance
• Protects the motor from debris and contact with moving components
• Helps reduce motor noise and vibration through stable mounting
• Resolves symptoms like excessive vibration, rubbing noises, or misaligned motor mounting

• One motor housing (white)

• Disconnect power to the appliance before starting any repair
• Typical installation requires removing panels and either the drum or motor access components; follow OEM instructions
• Handle housing edges carefully and retain all mounting hardware for reassembly

This planetary assembly is the drive gear housing that transfers motor torque into the appliance's rotating mechanism, restoring reliable movement and consistent operation. It's a direct-fit replacement when the original gear housing is worn or damaged. What it does:

• Translates motor rotation into the multi-gear motion needed for the appliance's rotating parts
• Restores smooth, quiet operation when worn or failing gears cause grinding or irregular movement
• Prevents further damage to surrounding components by replacing stripped or broken gear teeth
• Supports consistent performance under normal operating loads

• Disconnect power and follow all safety procedures before servicing
• Access may require removing the appliance cabinet or specific panels; keep fasteners organized
• Inspect related seals, bearings, and mounting hardware and replace if damaged

This Empire red touch-up paint restores the original appliance finish to cover chips, scratches, and small blemishes for a clean, uniform look. Ideal for maintaining the appliance's appearance between larger repairs or panel replacements. What it does:

• Matches the Empire Red appliance color to conceal chips and surface scratches
• Prevents small bare spots from showing and improves overall cosmetic appearance
• Helps maintain consistent color on exterior panels and trim
• Useful for spot repairs after minor impacts or wear

• Clean and dry the surface thoroughly; remove grease and loose paint before applying
• Apply in thin coats, allowing recommended dry time between coats for best results
• Test on an inconspicuous area first to confirm color match
• Follow all product label warnings; use in a well-ventilated area and keep away from heat and open flame

A white replacement bowl support that centers and stabilizes the appliance bowl or glass tray to reduce wobble and noise, helping restore smooth rotation and reliable operation. What it does:

• Centers and supports the bowl or glass tray to prevent off-center rotation and rubbing.
• Keeps the tray steady to reduce vibration and noisy operation.
• Helps the tray rotate smoothly for even heating or proper function.
• Common symptoms it can address: wobbling or off-center bowl/tray, noisy rotation, scraping or unstable tray movement.

• Disconnect power to the appliance before starting any work.
• Remove the bowl or glass tray and lift out the old support; inspect the drive hub or shaft for damage.
• Align the support over the hub/shaft and press into place until fully seated; do not force broken or warped plastic.

This base feet assembly provides the lower support for the appliance, helping keep it stable, level, and protected from floor contact. Replaces worn or damaged base feet to reduce rocking and uneven operation. What it does

• Supports the appliance weight and maintains proper clearance from the floor
• Helps level the appliance to prevent rocking, vibration, and noise
• Protects flooring by preventing direct metal-to-floor contact
• Reduces movement during cycles or when doors are opened

• One base feet assembly

• Disconnect power (and water if applicable) before servicing for safety
• Installation may require lifting or tipping the appliance; use a second person or proper lifting tools
• Use basic hand tools; follow factory service instructions for correct fit and leveling
• Do not overtighten mounting fasteners; adjust feet evenly to achieve proper level

This bowl and foot assembly replaces a cracked or worn support bowl used to stabilize and support the appliance's internal component, restoring proper alignment and quiet operation. Durable molded construction suits direct-replacement needs. What it does:

• Supports and centers internal components to maintain smooth rotation and balance
• Replaces damaged, cracked, or warped bowl/foot that can cause rattling or uneven operation
• Restores correct spacing to prevent contact between moving parts and the cabinet
• Matches factory fit and finish for a secure, stable installation

• Disconnect power before beginning any repair to avoid electrical hazard
• Handle with care to avoid cracking the plastic; use gentle force when seating into place
• Basic hand tools may be needed to access the mounting area; model-specific diagram for access