Columbia Snow Removal Equipment Control Cable

This lift cable is designed for use with many lawnmowers and snowblowers to ensure that the gears run smoothly while using the equipment. The lift cable is made of durable materials but has delicate connectors on each end which may eventually wear out. When the connectors or cables are damaged, the part will need to be replaced. This component is important since it helps control how fast the blades or other parts of the tool can operate. If the cable breaks, the tool may not start.If the lift cable has gone bad, is worn out, or is damaged, replacement is needed. There will be no need to use tools during the process, but work gloves can be helpful. The lift cable can be untwisted from the housing and removed from the tool. Take the new component and place it in the same location. Make sure to reassemble any additional parts before useThis is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The lift cable is made to fit lawnmowers and snowblowers manufactured by Craftsman, Toro, Cub Cadet, Troy-Bilt, MTD, Huskee, Montgomery Wards, and Yard-Man.

The snowblower auger cable initiates operation of the snowblower’s auger similar to the cable on the handle of a push mower. To start the snowblower, the control handle must be squeezed. This engages the snowblower auger cable to allow the auger to begin turning. When the snowblower auger cable is broken, the snowblower cannot work because the auger will not turn. The length of this snowblower auger cable is 47.48 inches. It is made from high-quality rubber insulation of a metal wire. A pair of pliers and a wrench are needed to complete the repair. If the snowblower still does not work after replacing the snowblower auger cable, check the shear pin as these are prone to breaking and will also prevent the auger from turning. This genuine OEM snowblower auger cable is compatible with snowblowers manufactured by Craftsman, Cub Cadet, Husky, MTD, Troy-Bilt, Yard Machines, and Yard-Man. This part is sold individually. You will need to order any hardware, housing, and the trigger separately if these items also need repair or replacement.

This part is a speed select cable. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or detached speed select cable on certain snowblower models. The speed select cable works by fastening the ground drive system to the speed control level. This enables the equipment operator to properly control speed and traction while using a snowblower. Over time, speed select cables can experience wear and tear which can cause them to break or become detached, requiring replacement. Without a functioning speed select cable, the snow blower will not be able to be properly controlled. For accurate information on how and where to install this replacement speed select cable, specific manufacturer diagrams should be referenced. Proper safety measures should always be followed when working on any type of equipment.As an authentic replacement part, this speed select cable can be used on multiple different models of Craftsman, MTD, Yard-Man, and Huskee snow blowers. Please note that this speed select cable is a genuine part made of high-quality materials and is sold individually.

This genuine MTD speed selector cable attaches the speed control lever to the snowblower's ground drive system to regulate and maintain the speed of the snowblower.Though speed selector cables are highly durable, they can be subject to damage as a result of exposure to inclement weather, impact upon collision, and general decline. Signs of a damaged speed selector cable can include malfunctioning regulation of speed, an overheating engine, or black smoke rising from the engine. If any of these symptoms occur, the speed selector cable should be checked and replaced immediately, as the snowblower cannot function properly without it. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This speed selector cable is compatible with the following brands: MTD, Troy-Bilt, Cub Cadet, Yard Machines, and Craftsman. Part sold individually.

The drive clutch cable is a clutch or engagement cable that tightens the drive belt or lifts the spinning friction disc contained within the drive housing. It will cause contact between the driveshaft and turn the wheels. If the wheels refuse to turn, it may be due to a cable that is damaged, loose, or snapped. If tightening the tension fails to yield results, this OEM replacement cable is needed. Replacing a drive clutch cable is fairly easy. Remove the original and use pliers and a socket set to install and tighten the new one. "This is a drive clutch cable designed for use in snowblowers produced by MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Huskee, Yard-Man, and others. It ships individually and is made of rubber, wire, and metal.

This is a drive cable that is used in many models of snowblowers from top manufacturers. It is composed of a metal cable that is inserted into a flexible plastic housing. The purpose of the drive cable is to connect the drive control located in the snowblower engine handle. It makes sure that the snowblower starts and stops when the controls are used. If the drive cable is broken or becomes damaged, the snowblower will not work correctly even if the control handle is released.If a snowblower isn't starting or stopping when expected, the drive cable is likely the source of the problem. The part needs to be replaced before the snowblower can be used again. Disconnect the spark plug wire before releasing the handle cables and removing the drive cover. Replace the drive cable and reassemble the other parts.This is an authentic OEM replacement drive cable that is sourced directly from the manufacturer. It is sold as an individual component. The drive cable is designed to be compatible with snowblowers manufactured by Yard-Man, Huskee, MTD, Yard Machines, Troy-Bilt, Cub Cadet, and Craftsman.