Parts for Lg MA-1164M: Complete Microwave Parts

This duct directs exhausted air from the dryer to the external vent, helping maintain proper airflow and improve drying performance. It replaces a damaged or disconnected exhaust passage to reduce leaks and venting issues. What it does

• Channels hot, moist air from the dryer to the outside to help clothes dry efficiently
• Restores a sealed exhaust path to reduce vent leaks and indoor lint buildup
• Helps reduce overheating and extended dry cycles caused by restricted airflow
• Addresses symptoms like poor drying performance, unusual vent smells, or visible duct damage

• Disconnect power before servicing the dryer.
• Remove the dryer or access panel as required to reach and replace the duct; secure all clamps or fasteners to prevent leaks.
• Inspect adjoining seals and venting for lint buildup or damage; replace or clean as needed.
• Follow OEM instructions for routing and clearances to avoid kinks or compression of the duct.

This thermostat controls refrigerator temperature to help maintain proper cooling and prevent spoilage. It replaces a failed or inaccurate temperature control to restore consistent operation. What it does:

• Senses internal temperature and signals the compressor to cycle on/off
• Helps keep food at steady, safe temperatures when functioning correctly
• Commonly replaces thermostats that cause warm temperatures or inconsistent cooling
• Works as a direct replacement when matching the OEM part number

• Always disconnect power to the appliance before servicing to avoid shock or injury
• Handle the sensor and terminals carefully; avoid bending or damaging components
• Basic hand tools are typically required; follow your model's service manual for exact instructions

Mounting screw for microwave assembly. Secures internal or external components. Replace if stripped, missing, or damaged during repair or installation.

Size: Approx 13 inches. Glass.

Secures interior panels and components. Replace when stripped, corroded, or missing to stop rattles and secure loose trim. Verify fit with your model number.

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

The Switch, Micro is an OEM part for LG microwaves. This micro switch is crucial for the operation of the microwave door mechanism, ensuring that the microwave only operates when the door is securely closed.

Causes of a bad micro switch can include wear and tear from frequent use, damage due to electrical faults, or physical impact that disrupts its functionality.

Symptoms of a bad micro switch include:

• The microwave not starting or stopping unexpectedly
• The door not latching properly
• The microwave light not turning on or off correctly
• Error messages appearing on the control panel

This OEM LG part is also compatible with Sears/Kenmore models.