Parts for Thermador T30IF70CSS: Compressor Condenser Parts

This replacement cover restores the appliance's exterior fit and helps protect internal components from dirt and moisture. It provides a clean finish and helps keep moving parts shielded for reliable operation. What it does:

• Protects internal components and wiring from debris and moisture
• Restores original fit, finish and alignment of the affected area
• Helps reduce noise caused by loose or exposed parts
• Prevents accidental contact with small moving components
• Useful when a cracked, missing or faded cover affects appearance or function

• Disconnect power and water before beginning work.
• Confirm correct orientation and seating before fastening; some covers snap into position while others use screws.
• Use appropriate hand tools and avoid over-tightening to prevent cracking.

A replacement shock absorber that cushions and appliance component to reduce noise and stabilize movement for smoother, more controlled operation. Restores dampening to doors or tubs that close unevenly or vibrate. What it does:

• Dampens and slows movement to prevent slamming and reduce impact wear
• Stabilizes panels or tubs to cut down on vibration and rattling sounds
• Helps maintain even, controlled closing and opening motion
• Commonly used when a door feels loose, drops, or closes too quickly

• Disconnect power (and water if applicable) before attempting service
• Retain original mounting hardware; only replace items explicitly listed as included
• Ensure correct orientation and secure fasteners; test operation after installation

Fix water dispenser not working or leaking with this outlet valve. Controls water flow from reservoir to dispenser. Moderate 30-45 minute repair.

Base panel for freezer models. Replacement for cracked, broken, or missing bottom trim panel. Installs at the base of the unit to restore appearance.

This shock absorber cushions and controls dishwasher door movement to reduce slamming and improve closing action. It helps protect the door and cabinet from impact and can reduce noise during operation. What it does:

• Dampens and slows the dishwasher door as it opens and closes
• Helps prevent sudden drops or slamming that can damage the door or hinges
• Reduces vibration and noise caused by uncontrolled door movement
• Restores smoother, more controlled door operation when the original shock wears out

• One shock absorber

• Disconnect power to the appliance before beginning any repair
• Remove the dishwasher door panels or access panels to reach the mounting points
• Support the door during removal/installation to prevent it from falling or binding
• Use the OEM mounting hardware and verify secure attachment and correct alignment after installation

Freezer not cooling or running constantly? This compressor is the heart of your cooling system. Requires technical skill and refrigerant handling.

Power cord for refrigerators and freezers. Connects appliance to wall outlet. Replace if cord is frayed, damaged, cracked, or missing its prongs.

Condensate water container collects moisture from your refrigerator's cooling system. Replace if cracked, broken, or leaking to prevent water damage.

Fixes incorrect temperature readings or frequent cycling. This thermistor monitors compartment temp for proper cooling. Moderate DIY repair, 30-45 minutes.

Base panel for refrigerator and freezer models. Replaces cracked, broken, or missing bottom panels. Restores structural integrity and appearance.

This is a protective housing or case that encloses an internal component in a range or oven. It shields the enclosed part from heat, moisture, or physical damage during operation. Replace this housing if it is cracked, warped, or damaged, which could leave internal components exposed and vulnerable to malfunction.

Mounting clip for refrigerator interior components. Secures shelves, bins, or panels in place. Replace if cracked, broken, or missing for proper fit.

Fix control panel issues or unit not responding with this refrigerator control transformer. Steps down voltage to power electronic controls reliably.

Interior mounting plate for bottom-mount refrigerators and freezers. Replaces cracked, broken, or missing plates that secure internal components.

Adhesive mounting tape secures trim, wiring, and small components while reducing rattles and moisture intrusion. Replace when worn or loose. Verify fit with your model number before ordering.

Replace a cracked or missing housing cover that exposes internal components to debris and moisture. Restores proper sealing and component protection.

This is a housing component used inside the freezer section of the refrigerator. It serves as a protective enclosure for internal parts such as sensors, lights, or fan assemblies, helping to keep them properly positioned and shielded. Replace this housing if it is cracked, broken, or warped, which can affect the proper operation of the components it protects.

Retaining washer for freezer and refrigerator internal assemblies. Secures components in place. Replace if cracked, broken, or missing during repairs.

This is a wheel assembly designed for use in a refrigerator or freezer. It supports the smooth rolling movement of components such as drawers, baskets, or the unit itself. Replace this wheel if it is cracked, worn, or no longer rolling freely, which can cause drawers to stick or the appliance to be difficult to move.

This is a filter drier used in the sealed refrigeration system to remove moisture and contaminants from the refrigerant lines. It is a small cylindrical component typically located along the refrigerant tubing between the condenser and the capillary tube. Replace this part if the refrigerator or freezer is not cooling properly due to a restricted or saturated drier, typically during a sealed system repair.

If your refrigerator cabinet feels warm or cooling is weak, the condenser fan may have failed. This fan circulates air over the condenser coil to remove heat.

Fixes ice maker overflow and water leaking into freezer. This water inlet valve controls water flow to your dispenser and ice maker. DIY repair.

Leveling foot installs at the refrigerator base to support and level the unit. Replace if worn, cracked, broken, or missing to restore stability.

Secures the water filter in your refrigerator for a snug, leak-free fit. Replace if lost during filter changes, cracked, damaged, or worn out over time.

Removes impurities from your refrigerator's water and ice supply. Replace every 6 months for clean, fresh-tasting water. Verify fit by model number.