Parts for Bosch B30IR70NSP/07: Compressor Parts

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

Fix a refrigerator that won't cool or runs constantly with a new compressor. This critical component circulates refrigerant to maintain proper temperatures.

This replacement cover restores the appliance's exterior fit and helps protect internal components from dirt and moisture. It provides a clean finish and helps keep moving parts shielded for reliable operation. What it does:

• Protects internal components and wiring from debris and moisture
• Restores original fit, finish and alignment of the affected area
• Helps reduce noise caused by loose or exposed parts
• Prevents accidental contact with small moving components
• Useful when a cracked, missing or faded cover affects appearance or function

• Disconnect power and water before beginning work.
• Confirm correct orientation and seating before fastening; some covers snap into position while others use screws.
• Use appropriate hand tools and avoid over-tightening to prevent cracking.

Refrigerator not cooling or running constantly? The condenser coil releases heat from the system. Moderate DIY repair requiring coil cleaning or replacement.

Fix control panel issues or unit not responding with this refrigerator control transformer. Steps down voltage to power electronic controls reliably.

Power cord for refrigerators and freezers. Connects appliance to wall outlet. Replace if cord is frayed, damaged, cracked, or missing its prongs.

Leveling foot installs at the refrigerator base to support and level the unit. Replace if worn, cracked, broken, or missing to restore stability.

Fix water dispenser not working or leaking with this outlet valve. Controls water flow from reservoir to dispenser. Moderate 30-45 minute repair.

Mounting clip for refrigerator interior components. Secures shelves, bins, or panels in place. Replace if cracked, broken, or missing for proper fit.

Fixes incorrect temperature readings or frequent cycling. This thermistor monitors compartment temp for proper cooling. Moderate DIY repair, 30-45 minutes.

Restores smooth winding and secure routing for internal cables or hoses. Replace if cable snags, rubs, or routes loosely. Confirm fit with your model number.

Replace a cracked or missing housing cover that exposes internal components to debris and moisture. Restores proper sealing and component protection.

This is a replacement dryer complete assembly designed to restore drying function and structure for compatible Bosch laundry units. It provides the main cabinet and drum enclosure needed for normal tumbling and airflow. What it does

• Houses the drum and internal components so clothes can tumble during the drying cycle
• Provides the enclosure and mounting points for the blower, heating system, and controls
• Restores proper airflow pathways to help the dryer heat and vent as intended
• Helps eliminate issues caused by damaged or severely warped cabinet or drum housings

• One complete dryer assembly as shown

• Disconnect power before servicing
• Follow factory service manual for alignment, seal, and vent reconnection steps
• Inspect and replace any worn seals, ducts, or mounting hardware as needed during installation

Interior mounting plate for bottom-mount refrigerators and freezers. Replaces cracked, broken, or missing plates that secure internal components.

Hearing rattling or loose parts inside your refrigerator? This mounting bracket secures internal components to eliminate noise and restore proper alignment.

Base panel for refrigerator and freezer models. Replaces cracked, broken, or missing bottom panels. Restores structural integrity and appearance.

Base panel for refrigerator bottom trim. Covers the base area beneath the doors. Replace if cracked, damaged, or missing to restore appearance.

Adhesive mounting tape secures trim, wiring, and small components while reducing rattles and moisture intrusion. Replace when worn or loose. Verify fit with your model number before ordering.

If your refrigerator cabinet feels warm or cooling is weak, the condenser fan may have failed. This fan circulates air over the condenser coil to remove heat.

If your refrigerator cabinet feels warm or cooling is weak, the condenser fan may have failed. This fan circulates air over the condenser coil to remove heat.

This shock absorber cushions and controls dishwasher door movement to reduce slamming and improve closing action. It helps protect the door and cabinet from impact and can reduce noise during operation. What it does:

• Dampens and slows the dishwasher door as it opens and closes
• Helps prevent sudden drops or slamming that can damage the door or hinges
• Reduces vibration and noise caused by uncontrolled door movement
• Restores smoother, more controlled door operation when the original shock wears out

• One shock absorber

• Disconnect power to the appliance before beginning any repair
• Remove the dishwasher door panels or access panels to reach the mounting points
• Support the door during removal/installation to prevent it from falling or binding
• Use the OEM mounting hardware and verify secure attachment and correct alignment after installation

Condensate water container collects moisture from your refrigerator's cooling system. Replace if cracked, broken, or leaking to prevent water damage.

Base panel for freezer models. Replacement for cracked, broken, or missing bottom trim panel. Installs at the base of the unit to restore appearance.

A replacement shock absorber that cushions and appliance component to reduce noise and stabilize movement for smoother, more controlled operation. Restores dampening to doors or tubs that close unevenly or vibrate. What it does:

• Dampens and slows movement to prevent slamming and reduce impact wear
• Stabilizes panels or tubs to cut down on vibration and rattling sounds
• Helps maintain even, controlled closing and opening motion
• Commonly used when a door feels loose, drops, or closes too quickly

• Disconnect power (and water if applicable) before attempting service
• Retain original mounting hardware; only replace items explicitly listed as included
• Ensure correct orientation and secure fasteners; test operation after installation