Parts for Frigidaire LCE441PL1: 03 - Console, Controls And Drum Parts

Washer not heating water properly or selecting wrong temperatures? This temperature switch controls water temperature settings. Common repair for temperature issues.

Fix a washer dryer combo that won't advance cycles or start properly with this timer control board. Resolves cycle timing issues in combo units.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

This part has been discontinued by the manufacturer and is no longer available.

Washer for oven fan motor mounting assembly. Replaces cracked, worn, or missing washers that secure the motor. Essential hardware for proper installation.

Seals the lint housing to prevent air leaks and maintain drying efficiency. Replace if worn, cracked, or causing lint buildup. Confirm fit with your model.

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Color: white. It measures about 12 inches wide by 7 inches high.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

A small molded clip that secures appliance wiring and harnesses to the cabinet, helping keep wires in place and reducing wear or rubbing. Use this clip when a loose or shifted harness needs a reliable anchor point. What it does:

• Fastens wiring or harnesses to the cabinet to prevent movement and chafing
• Keeps wires routed away from heat, moving parts, and sharp edges
• Helps reduce vibration noise caused by loose wiring
• Can prevent intermittent electrical issues caused by damaged insulation or connectors

• Disconnect power before accessing internal wiring or panels
• Remove the panel or trim needed to reach the original clip location
• Press the clip into the factory mounting hole or snap the wire into the clip until secure
• Inspect nearby wiring and harnesses for damage; replace any damaged wiring before reassembly

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

A small molded clip that secures appliance wiring and harnesses to the cabinet, helping keep wires in place and reducing wear or rubbing. Use this clip when a loose or shifted harness needs a reliable anchor point. What it does:

• Fastens wiring or harnesses to the cabinet to prevent movement and chafing
• Keeps wires routed away from heat, moving parts, and sharp edges
• Helps reduce vibration noise caused by loose wiring
• Can prevent intermittent electrical issues caused by damaged insulation or connectors

• Disconnect power before accessing internal wiring or panels
• Remove the panel or trim needed to reach the original clip location
• Press the clip into the factory mounting hole or snap the wire into the clip until secure
• Inspect nearby wiring and harnesses for damage; replace any damaged wiring before reassembly

This cable tie secures wiring and small hoses inside the appliance to prevent rubbing, snagging, and vibration-related movement. It's a simple replacement part for restoring proper wire routing and keeping components tidy and safe. What it does:

• Holds wiring harnesses and loose cables in place to reduce wear and chafing
• Helps prevent wiring from contacting hot or moving parts
• Reduces noise caused by loose wires or hoses
• Keeps connectors and lines routed for reliable operation

• Disconnect power to the appliance before servicing
• Route wiring as shown in the appliance wiring diagram or photos, then cinch the tie snugly—do not overtighten
• Trim excess tail and ensure the tie does not stress the wire insulation
• Replace any damaged wiring or insulation discovered during installation

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

This is a small spring that attaches to the lid of a laundry center washer, providing tension to hold the lid in position. It helps the lid stay open during loading and close securely during operation. Replace this spring if your washer lid won't stay open, slams shut on its own, or the original spring is broken or stretched out.