Parts for Kenmore 417.99160110 (41799160110, 417 99160110): Console Controls, Drum Parts

Fix a washer dryer combo that won't advance cycles or start properly with this timer control board. Resolves cycle timing issues in combo units.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

This replacement timer knob restores user control of the washer's cycle dial, letting you select and change wash cycles easily. It replaces a cracked, stripped, or loose knob so the timer dial is easy to turn and read. What it does:

• Fits onto the washer timer shaft and provides a firm grip for turning the cycle selector
• Allows selection and adjustment of wash cycles and settings without slipping
• Replaces knobs that are cracked, broken, loose, or have stripped splines
• Helps restore normal user control of the timer dial

• Disconnect power to the washer before servicing.
• Pull the old knob straight off the splined shaft (some models use a retaining clip—remove first if present).
• Align the replacement knob's splines with the shaft and push it on until fully seated; do not force.
• After installation, restore power and verify the knob turns smoothly and selects cycles correctly.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

Washer for oven fan motor mounting assembly. Replaces cracked, worn, or missing washers that secure the motor. Essential hardware for proper installation.

Seals the lint housing to prevent air leaks and maintain drying efficiency. Replace if worn, cracked, or causing lint buildup. Confirm fit with your model.

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Color: white. It measures about 12 inches wide by 7 inches high.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

A small molded clip that secures appliance wiring and harnesses to the cabinet, helping keep wires in place and reducing wear or rubbing. Use this clip when a loose or shifted harness needs a reliable anchor point. What it does:

• Fastens wiring or harnesses to the cabinet to prevent movement and chafing
• Keeps wires routed away from heat, moving parts, and sharp edges
• Helps reduce vibration noise caused by loose wiring
• Can prevent intermittent electrical issues caused by damaged insulation or connectors

• Disconnect power before accessing internal wiring or panels
• Remove the panel or trim needed to reach the original clip location
• Press the clip into the factory mounting hole or snap the wire into the clip until secure
• Inspect nearby wiring and harnesses for damage; replace any damaged wiring before reassembly

Red adhesive strip for washers. Secures components and panels inside the cabinet. Replace if peeling, missing, or no longer holding parts in place.

Dryer not heating or overheating? This resistor regulates temperature control in your dryer's heating system. Simple DIY replacement part.

This part has been discontinued by the manufacturer and is no longer available.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

The dryer timer power resistor regulates electrical current to the timer motor in mechanical timer systems. Replace when the timer fails to advance properly, gets stuck in cycles, or the dryer runs continuously without stopping.

Suspension spring that supports and stabilizes the wash tub during operation. Replace if broken, cracked, or worn to restore proper tub support.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.