Parts for Kenmore 417.99165130 (41799165130, 417 99165130): Console Controls, Drum Parts

Fix a washer dryer combo that won't advance cycles or start properly with this timer control board. Resolves cycle timing issues in combo units.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

This replacement timer knob restores user control of the washer's cycle dial, letting you select and change wash cycles easily. It replaces a cracked, stripped, or loose knob so the timer dial is easy to turn and read. What it does:

• Fits onto the washer timer shaft and provides a firm grip for turning the cycle selector
• Allows selection and adjustment of wash cycles and settings without slipping
• Replaces knobs that are cracked, broken, loose, or have stripped splines
• Helps restore normal user control of the timer dial

• Disconnect power to the washer before servicing.
• Pull the old knob straight off the splined shaft (some models use a retaining clip—remove first if present).
• Align the replacement knob's splines with the shaft and push it on until fully seated; do not force.
• After installation, restore power and verify the knob turns smoothly and selects cycles correctly.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

This part has been discontinued by the manufacturer and is no longer available.

Washer for oven fan motor mounting assembly. Replaces cracked, worn, or missing washers that secure the motor. Essential hardware for proper installation.

Seals the lint housing to prevent air leaks and maintain drying efficiency. Replace if worn, cracked, or causing lint buildup. Confirm fit with your model.

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Color: white. It measures about 12 inches wide by 7 inches high.

This cable tie secures wiring and small hoses inside the appliance to prevent rubbing, snagging, and vibration-related movement. It's a simple replacement part for restoring proper wire routing and keeping components tidy and safe. What it does:

• Holds wiring harnesses and loose cables in place to reduce wear and chafing
• Helps prevent wiring from contacting hot or moving parts
• Reduces noise caused by loose wires or hoses
• Keeps connectors and lines routed for reliable operation

• Disconnect power to the appliance before servicing
• Route wiring as shown in the appliance wiring diagram or photos, then cinch the tie snugly—do not overtighten
• Trim excess tail and ensure the tie does not stress the wire insulation
• Replace any damaged wiring or insulation discovered during installation

A small molded clip that secures appliance wiring and harnesses to the cabinet, helping keep wires in place and reducing wear or rubbing. Use this clip when a loose or shifted harness needs a reliable anchor point. What it does:

• Fastens wiring or harnesses to the cabinet to prevent movement and chafing
• Keeps wires routed away from heat, moving parts, and sharp edges
• Helps reduce vibration noise caused by loose wiring
• Can prevent intermittent electrical issues caused by damaged insulation or connectors

• Disconnect power before accessing internal wiring or panels
• Remove the panel or trim needed to reach the original clip location
• Press the clip into the factory mounting hole or snap the wire into the clip until secure
• Inspect nearby wiring and harnesses for damage; replace any damaged wiring before reassembly

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Red adhesive strip for washers. Secures components and panels inside the cabinet. Replace if peeling, missing, or no longer holding parts in place.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Suspension spring that supports and stabilizes the wash tub during operation. Replace if broken, cracked, or worn to restore proper tub support.