Parts for Frigidaire DEC310A1W: 05 - Console, Controls, Heat Assy. Parts

This part has been discontinued by the manufacturer and is no longer available.

Hex washer head ,10-32 x 0.375. Ground

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This lock washer secures fasteners and helps keep appliance panels and components from loosening during normal use, restoring a stable connection and reducing rattles or movement. What it does

• Grips under a screw or bolt to resist loosening from vibration and thermal cycling
• Helps keep panels, brackets, and small components securely fastened
• Commonly used where a screw or bolt must stay tight despite vibration
• Can reduce rattling noises and intermittent loose-part symptoms

• Disconnect power to the appliance before beginning any repair
• Replace with the same type and orientation of washer for proper locking action
• Use appropriately sized screw or bolt; do not mix with mismatched hardware
• Hand-start fasteners, then tighten to snug fit—avoid over-tightening which can deform the washer

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This retainer lead wire secures appliance wiring to keep harnesses organized and away from heat or moving parts, reducing wear and accidental disconnection. It's a simple replacement to restore proper wire routing and protection. What it does:

• Clips or holds the wiring harness in place to prevent chafing and strain
• Helps keep wires away from hot surfaces, vents, or moving components
• Reduces risk of intermittent electrical connections caused by loose wiring
• Restores factory routing after service or component replacement

• Disconnect power to the appliance before installing to avoid shock or injury
• Remove any panels necessary to access the original retainer and wiring route
• Replace like-for-like, seating the retainer securely so the harness cannot shift
• If wires show damage or insulation wear, inspect further and replace damaged wiring before reassembly

Sound dampening insulation for dryers. Installs inside cabinet to reduce noise and vibration. Replace if torn, missing, or deteriorated over time.

A small molded clip that secures appliance wiring and harnesses to the cabinet, helping keep wires in place and reducing wear or rubbing. Use this clip when a loose or shifted harness needs a reliable anchor point. What it does:

• Fastens wiring or harnesses to the cabinet to prevent movement and chafing
• Keeps wires routed away from heat, moving parts, and sharp edges
• Helps reduce vibration noise caused by loose wiring
• Can prevent intermittent electrical issues caused by damaged insulation or connectors

• Disconnect power before accessing internal wiring or panels
• Remove the panel or trim needed to reach the original clip location
• Press the clip into the factory mounting hole or snap the wire into the clip until secure
• Inspect nearby wiring and harnesses for damage; replace any damaged wiring before reassembly

A small molded clip that secures appliance wiring and harnesses to the cabinet, helping keep wires in place and reducing wear or rubbing. Use this clip when a loose or shifted harness needs a reliable anchor point. What it does:

• Fastens wiring or harnesses to the cabinet to prevent movement and chafing
• Keeps wires routed away from heat, moving parts, and sharp edges
• Helps reduce vibration noise caused by loose wiring
• Can prevent intermittent electrical issues caused by damaged insulation or connectors

• Disconnect power before accessing internal wiring or panels
• Remove the panel or trim needed to reach the original clip location
• Press the clip into the factory mounting hole or snap the wire into the clip until secure
• Inspect nearby wiring and harnesses for damage; replace any damaged wiring before reassembly

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.