Parts for Frigidaire 7308-87E: Console / Controls / Top Panel Parts

The dryer timer power resistor regulates electrical current to the timer motor in mechanical timer systems. Replace when the timer fails to advance properly, gets stuck in cycles, or the dryer runs continuously without stopping.

Replace a broken or worn control panel pushbutton on your dryer. This button installs on the control panel to restore manual operation and appearance.

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

This switch allows you to select different heat settings on your dryer for various fabric types. It controls the heating element operation to provide low, medium, and high temperature options. If your dryer only heats on one setting or doesn't heat at all when you change temperature selections, this switch likely needs replacement.

Secures wiring harness to prevent chafing and maintain safe wire routing in washers, dryers, and laundry appliances. Replace if loose or broken. Check your model for compatibility.

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

Replace your dryer's timer dial if it's cracked, broken, or won't turn properly. This control dial mounts on the timer shaft to set drying cycles.

This part has been discontinued by the manufacturer and is no longer available.

This top panel is the painted metal cover that sits on the range's upper surface, restoring a clean appearance and protecting internal components from spills and heat. It replaces worn, dented, or discolored top covers. What it does:

• Covers and protects the range's front/top area and underlying components from spills and debris
• Restores the appliance's finished appearance after dents, chips, or paint wear
• Helps maintain proper spacing for controls and trim pieces
• Stops light cosmetic drafts and prevents direct access to internal wiring

• Disconnect power to the appliance before beginning any work.
• Remove cooktop or control trim as needed to access mounting screws; keep hardware for re-use.
• Support the panel during removal and installation to avoid scratching surrounding surfaces.

This ground wire provides a secure electrical ground connection for your appliance's chassis to help prevent electrical shock and ensure safe operation. It replaces a damaged or missing grounding lead. What it does:

• Connects the appliance chassis to the grounding point to safely dissipate stray current
• Restores proper grounding after corrosion, fraying, or accidental damage
• Helps eliminate intermittent electrical faults caused by a poor ground
• Works where a single grounding lead is required for the component or cabinet

• One ground wire

• Turn off and unplug the appliance (or disconnect power at the breaker) before starting any work
• Verify the original grounding point and wire routing before removal to match reinstallation
• Use appropriate tools to remove and reinstall fasteners; ensure tight, clean metal-to-metal contact