Parts for Ge AGBS300PJ2WW: 02 - Control Panel & Cooktop Parts

Color: Black

Color: White. This is the left side end cover. For right side use WB07K10001.

Color: Whie. This is the right side end cover. For left side use WB07K10002.

This is the right side end plate. For left side use WB37K15.

This is the left side end plate. For right side use WB37K14.

Color: White. Mounting screw for end caps.

This is the right side guide holder. For left side use WB14K2.

This is the left side guide holder. For right side use WB14K1.

This gas burner grate supports cookware on a gas cooktop, restoring stable, level support for safer, more consistent cooking. It replaces a cracked, warped or missing grate so pots and pans sit securely over the burner. What it does:

• Provides a stable surface for cookware so pans sit level over the flame.
• Helps maintain consistent heat contact for more even cooking.
• Replaces broken, chipped, warped or missing grates that cause wobbling or uneven heating.
• Designed to fit the designated cooktop burner location for correct alignment.

• Allow the cooktop to cool and turn all controls to OFF before replacing the grate.
• Remove the old grate and set the new grate into position—no tools are typically required.
• Inspect surrounding burner caps and ignitors; do not operate burners if any components are damaged.
• If you smell gas or suspect a leak, shut off the gas supply.

This is the main top.

Color: White. This is the left side end cap. For right side use WB07K10005.

Color: White. This is the right side end cap. For left side use WB07K10007.

This is the right side guide slide.

This is the left side guide slide. For right side use WB14K3.

This hinge pin links the oven door hinge to its mounting point, creating the pivot that lets the door open and close smoothly. Replacing a worn or missing pin can restore steady door movement and a consistent seal.

• Serves as the pivot point for the door hinge
• Helps maintain proper door alignment and closing pressure
• Wear or damage may show as a loose, sagging, or misaligned door
• May help address squeaks, binding, or difficulty latching the door

• Disconnect power; for gas ranges, also shut off the gas supply
• Support or remove the door to access the hinge
• Note hinge orientation; remove the old pin and install the new pin securely
• Inspect the hinge/bracket for wear; lubricate only if specified by the manufacturer

This factory screw secures components on GE cooking appliances. Replacing a lost or stripped fastener helps keep parts tight and aligned for safer, rattle-free operation.

• Fastens brackets, panels, trim, or burner components on a range, cooktop, or wall oven
• Replaces missing, corroded, or stripped hardware
• Helps reduce looseness, vibration, or rattling noises
• Restores proper alignment after service or cleaning

• Disconnect power and shut off gas supply. Allow the appliance to cool completely.
• Match this screw to the original and install in the same location.
• Use the correct driver; hand-tighten and avoid overtightening to prevent stripped threads or cracked parts.
• If mating threads are damaged, repair or replace the affected component before reassembly.

Color: White. Mounting screw for end caps.

Package of 12

This replacement screw secures appliance components so panels, brackets, and trim stay tight and aligned. Use it to replace a missing, stripped, or rusted fastener and restore a solid, rattle-free fit in the affected assembly.

• Fastens parts to the chassis/frame or mounting brackets
• Replaces lost, damaged, or corroded hardware
• Can help address loose or vibrating panels and minor misalignment
• Maintains a secure attachment during normal operation

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Match the screw to the original location and reuse any clips or washers if present
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Repair/replace damaged receiving threads or clip for proper hold