Parts for Ge JGBS20DEM2BB: 02 - Control Panel & Cooktop Parts

This end support secures and aligns the appliance drum/shaft assembly so the tub spins smoothly and quietly. Replacing a worn support restores proper drum position and reduces rubbing or wobbling during operation. What it does:

• Holds the drum/shaft in the correct position at the left front to maintain smooth rotation
• Provides a mounting surface and bearing area that prevents metal-on-metal contact
• Common symptom: loud scraping, grinding or thumping noises during spin
• Common symptom: visible drum wobble, rubbing or uneven rotation

• Disconnect power before any disassembly
• Remove outer panels and drum as needed to access the support; follow your model's service manual for steps
• Keep track of fasteners and note part orientation for correct reassembly
• Inspect adjacent parts for wear and replace if needed

End support cap for gas ranges. Installs on the side panel to provide structural support and a finished appearance. Replace if cracked or missing.

This right-side end support secures and aligns a refrigerator shelf/rail or drawer track so slides operate smoothly and stay in place. Replacing a damaged support restores proper shelf alignment and prevents drawers or bins from sagging. What it does

• Holds the end of a shelf rail or drawer track to keep sliding parts aligned
• Prevents shelves or drawers from sagging, binding, or falling out
• Reduces wobble or uneven movement when loading or sliding shelves/drawers
• Helps restore proper operation after a cracked, broken, or worn end bracket

• Disconnect power before working inside the refrigerator and remove food/items from affected area
• Remove the shelf, drawer, or rail to access the end support; note orientation for reassembly
• Require basic hand tools (screwdriver, nut driver) and light prying to release tabs or fasteners
• Reinstall components and test sliding action; discard damaged parts before reuse

Right end support cap for gas ranges. Secures and covers the side panel edge. Replace if cracked, broken, or missing to restore a finished appearance.

Right hand side

Left hand side

Color: Bisque

Color: Black

Color: White

If your gas range display is blank, oven won't heat, or temperature climbs uncontrollably, the control board likely failed. Moderately easy DIY repair.

Upper back cover panel for gas ranges. Replaces cracked, damaged, or missing housing cover on the rear upper section. Restores appearance and protects.

Replace the lower back cover panel on your gas range. This housing protects internal components and maintains structural integrity when cracked or damaged.

Color: White. Mounting screw for end caps.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

Fix burners that won't ignite or keep clicking with this ignition spark module. Controls high-voltage sparks for cooktop burners. DIY-friendly repair.

This is the right side guide holder. For left side use WB14K2.

Left side oven rack guide holder for gas ranges. Replaces broken, cracked, or missing guide holders that secure oven rack slides in position.

Black burner grate kit for gas range cooktops. Replaces scarred, chipped, or damaged grates. Sits over burners to support cookware during cooking.

Color: Gray. It measures about 8-1/2 inches wide by 8-1/2 inches deep. For black order WB31K10026.

Replace cracked, chipped, or discolored burner grates on your gas range. Provides a stable platform for cookware over the burner. Easy swap installation.

White metal cooktop main top for gas ranges. Replaces rusted, cracked, or damaged cooktops. Direct fit installation restores range appearance.

This standard rangetop is the replacement top assembly that restores a level, stable cooking surface and helps your range operate and look like new. It fits where the cooktop sits and supports burners and cookware. What it does:

• Replaces a damaged, dented or worn rangetop to restore a flat cooking surface
• Secures and aligns burner components for consistent burner performance
• Helps prevent heat and spill damage to underlying components
• Addresses symptoms like uneven cookware, rattling parts or visible top damage

What's included:

• One standard rangetop assembly

Install notes:

• Disconnect power and shut off gas supply before starting any repair
• Handle sharp edges carefully; use gloves and eye protection
• Lift and align the rangetop carefully to engage support clips/mounting points

Pin locator for gas ranges. Secures and aligns burner components in proper position. Replace if broken, missing, or worn to restore proper burner assembly.

Right side guide slide for gas range oven racks. Replace if cracked, bent, or causing racks to stick. Ensures smooth oven rack sliding operation.

Left side guide slide for gas ranges. Replaces cracked, broken, or worn slides. Essential structural component for proper range operation.

Pivot pin that connects the oven door hinge to its mounting bracket. Replace if worn, broken, or missing to restore smooth door operation and alignment.

Factory screw secures brackets, panels, trim, or burner components on ranges, cooktops, and wall ovens. Replaces missing, stripped, or corroded fasteners.

Color: Bisque

Black touch pad overlay for range control panel. Replaces worn, faded, or cracked overlays. Installs over existing control board for a refreshed appearance.

Replacement control panel overlay for your range. Covers the control board with printed labels and buttons. Needed when original is cracked, cut, or worn.

Package of 12

Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.

Hex washer head screw for electric ranges. Secures panels, brackets, and internal components. Replace if screw is stripped, missing, or damaged.