Parts for Ge CHS995SEL2SS: Control Panel & Cooktop Parts

The Range Top Glass and Front Support Kit is an OEM replacement part for GE electric ranges. As the protective surface above cooktop burners and the frame securing the glass panel, this kit plays an integral role. 

Symptoms of a bad glass top and support include:

• Cracks or chips in the glass cooking surface 
• Looseness, wobbling or movement of the glass panel
• Gaps appearing around the edges of the glass top

Over time, thermal expansion and contraction from cooking temperatures can cause the glass to weaken. Repeated scrubbing or impacts from cookware are also common causes of damage.

This genuine OEM GE part is also compatible with Hotpoint, RCA, and select Kenmore electric ranges.

This indicator sleeve is a small control-knob marker that restores a clear position marker and snug fit on the control shaft for reliable setting selection. It improves dial visibility and stabilizes the knob during use. What it does:

• Covers and centers the control shaft so the knob sits straight and turns smoothly
• Provides a visible pointer for selecting temperature or power settings
• Replaces cracked, worn or missing sleeves that make knob position hard to read
• Helps eliminate wobble or looseness between the knob and control shaft

• One indicator sleeve

• Disconnect power to the appliance before servicing
• Remove the control knob (pull straight off) to access the sleeve
• Press the sleeve onto the shaft by hand until fully seated; no special tools generally required
• If the knob or shaft is damaged, inspect and replace as needed for secure fit

This lower oven warming element heats the oven's warming/holding compartment so food stays warm until serving. Replaces a damaged or non-heating lower element to restore consistent low-temperature operation. What it does:

• Heats the oven's warming/lower compartment for holding cooked food
• Replaces elements that show visible damage, burn-through, or no heat output
• Helps restore even low-temperature performance when the warmer function fails
• Works with the oven's temperature control and safety circuits to provide steady heat

• One lower oven warming element

• Disconnect power at the breaker before beginning any repair
• Wear gloves; element edges and terminals may be sharp
• Verify proper wiring and secure terminal connections during installation

This induction cooktop element replaces a failed high-power burner to restore normal cooking performance on compatible induction ranges. It provides the heating coil assembly required for fast, responsive induction heating. What it does:

• Replaces the induction heating element that generates the magnetic field to heat cookware.
• Restores a burner that no longer heats, heats intermittently, or shows reduced power.
• Helps eliminate error conditions or cooktop lockouts caused by a faulty element.
• Matches the OEM wattage rating for high-output cooking performance.

• Disconnect power at the breaker before servicing; glass cooktops and wiring can be hazardous.
• Handle the glass surface and element assembly carefully to avoid cracks or damage.
• Installation may require removing the cooktop glass and disconnecting wiring—keep fasteners and wiring order noted.

Wing knob kit used for panelization installation on select range models. Replace missing, stripped, or damaged wing knobs to secure trim panels properly.

Trim kit for gas ranges. Installs around cooktop or control panel to cover gaps and provide a finished appearance. Replace if cracked or missing.

Fix an unresponsive or cracked touch control panel on your range. This glass and touch board assembly restores bake, broil, timer, and display functions.

Induction control and gasket kit manages cooking element power on electric ranges. Replace if elements won't heat, respond erratically, or show error codes.

Seals the air duct beneath your induction cooktop to maintain proper airflow and prevent heat or steam leakage. Replace when worn or damaged. Verify fit by model number.

Replacement 8-18 x 5/16 screw secures range panels, brackets, and components. Needed when original fastener is stripped, missing, or damaged.

Seals the gap between your range body and control panel to contain heat and prevent spills from entering internal components. Replace if heat escapes or moisture gets inside. Confirm fit by your model number.

A temperature probe that senses oven temperature and sends readings to the control board so the appliance can regulate cooking heat. Replaces a failed or intermittent probe to restore accurate temperature feedback. What it does

• Measures internal oven temperature and provides a signal to the oven control for proper temperature regulation
• Can cause inaccurate baking, uneven cooking, or oven error codes when faulty or open/shorted
• Works as the sensor input used by the control to heat cycles on/off
• Typically mounts inside the oven cavity and connects to the control harness

• One temperature probe (BLE) sensor

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle the probe and wiring gently; do not kink or sharply bend the sensor lead
• Verify connector alignment and secure fit to the control harness; test continuity per OEM instructions before full reassembly