Parts for HCC2220BEB: Control Panel & Cooktop Parts

This knob gasket is a small rubber seal that fits behind a range or oven control knob to improve knob fit and keep the control shaft protected from dirt and moisture. It restores a snug, finished appearance. What it does:

• Cushions and centers the control knob on the shaft to reduce wobble and improve operation
• Seals the control shaft opening to help keep food, grease and moisture out of the control panel
• Helps prevent premature wear of the knob and control shaft from direct contact
• Common symptom fixes: loose or tilted knob, visible gap around knob, dirt or moisture entering the control area

• One replacement knob gasket

• Disconnect power to the appliance before starting any repair; if servicing a gas range, turn off the gas supply.
• Pull the control knob straight off, remove the old gasket, and press the new gasket into the panel recess or over the shaft until seated.
• No special tools typically required; use a soft tool or cloth to avoid scratching the panel.
• If the knob or shaft is damaged, inspect those parts and replace as needed.

This front bracket is a factory-style mounting bracket that supports and secures the appliance's front frame or console components for stable alignment and fit. It restores proper mounting where a bracket is cracked, broken, or missing. What it does:

• Provides a secure mounting point for the appliance front frame/console to prevent sagging or movement
• Restores correct alignment of exterior panels and controls after damage or wear
• Helps eliminate rattles, gaps, or loose trim caused by a failed bracket
• Works as a direct replacement for the original style bracket used on compatible GE units

• One front bracket, single piece

• Disconnect power to the appliance before starting any repair
• Remove trim or panels as required to access the damaged bracket; keep fasteners for reuse if undamaged
• Use common hand tools; avoid over-tightening screws which can strip mounting points
• If mounting points are damaged, inspect surrounding structure and replace or reinforce as needed

This rear bracket is a replacement mounting bracket that secures internal components at the back of the appliance, restoring proper alignment and reducing movement. It's a direct-fit OEM-style part used where the original bracket is damaged or missing. What it does:

• Provides a secure mounting point for rear assemblies and components
• Restores proper alignment to reduce vibration, rattling, or shifting parts
• Helps maintain panel fit and structural support at the appliance rear
• Prevents contact between moving parts and the cabinet that can cause noise or wear

• Disconnect power to the appliance before beginning any repair
• Remove any rear or access panels as needed to reach the bracket
• Retain and reuse original fasteners when possible; replace damaged hardware

This insulator protects appliance wiring and terminal connections from shorting and abrasion, helping keep electrical connections safe and stable. Replace a damaged insulator to reduce arcing and restore reliable operation. What it does:

• Seats over a terminal or post to electrically isolate connections and prevent shorts
• Protects wiring and connectors from rubbing, heat damage, and mechanical wear
• Helps stop arcing or intermittent power caused by a cracked or melted insulator
• Commonly replaced when you see melting, cracking, burn marks, or loose wiring at the terminal

• Disconnect power before inspecting or replacing any electrical parts
• Remove only the damaged insulator and install the replacement in the same orientation
• Ensure terminals and wires are clean and properly seated before re-energizing
• If terminals show corrosion or heat damage, replace the terminal assembly per OEM guidance

Replace a double burner element that won't heat, heats unevenly, or stays on constantly. Common repair for electric cooktops. Moderate difficulty.

This replacement bracket secures a radiant cooktop element to the range, restoring proper support so the element sits level and stays firmly in place during use. Fits GE electric/range radiant elements. What it does:

• Holds the radiant heating element securely to the cooktop assembly to prevent movement or sagging
• Keeps the element properly aligned for consistent contact with terminals and reliable heating
• Addresses symptoms like a loose or wobbling burner, element that won't stay seated, or poor contact at the element terminals
• Durable metal construction designed to withstand normal cooktop temperatures

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the glass cooktop and element carefully to prevent cracking or cuts
• Remove the element and any trim as needed to access and replace the bracket; secure all mounting fasteners

This door gasket seals the fresh-food compartment door to maintain a tight refrigerant barrier and help keep food cold and fresh. It restores a proper seal when an old or damaged gasket allows air leaks. What it does:

• Replaces a worn, torn or deformed fresh-food door gasket to restore door sealing
• Helps reduce frost buildup and prevents warm air from entering the compartment
• Can improve cooling consistency and energy use by restoring the door seal
• Addresses symptoms such as warm food, excess frost/ice, or continuous compressor cycling

• One replacement door gasket

• Remove the old gasket and clean the door channel before installing the new gasket
• Start at one corner and work the gasket into the channel evenly to avoid twists or gaps
• Heat (hair dryer or warm water) can be used carefully to help form the gasket for a snug fit; avoid overheating

This ST4 2x8 self-tapping screw secures trim, panels, and internal components on compatible appliances for a tight, vibration-resistant fit. Use it to restore proper fastening where the original screw is stripped, missing, or damaged. What it does:

• Fastens sheet metal and plastic appliance parts where an ST4 2x8 screw is required
• Provides a secure, vibration-resistant hold for panels, brackets, and trim
• Replaces missing or damaged screws to stop rattling, loose panels, or misaligned parts
• Matches OEM fit and function when the original screw is lost or worn

• Use the correct screwdriver or bit to avoid stripping the head
• Start threads by hand if possible; drive carefully to avoid over-torquing or cracking plastic
• Disconnect power and follow all safety precautions before servicing the appliance
• Replace all like-for-like for best results