Parts for Electrolux EI30BM55HZC: 05 - Control Panel,Door,Miscellaneous Parts

This main electronic control manages refrigerator functions and user settings, restoring programmed cooling cycles and display/control responses when the original board fails. Replaces a failed or unresponsive control for cooler operation and interface control. What it does:

• Sends signals to compressor, fans, and defrost system to regulate temperatures
• Interprets user inputs and displays status from the control panel
• Helps correct intermittent or total loss of refrigerator cooling when board is defective
• Can resolve symptoms like unresponsive controls, incorrect temperatures, or no display/output

• One control board

• Unplug the appliance before starting and ensure power remains off while working
• Handle the board by its edges and avoid static discharge; use an anti-static wrist strap if available
• Compare new board to the old one and transfer any brackets or connectors as needed
• Reinstall all fasteners and restore power, then verify operation of controls and cooling

This replacement control-console front panel restores the appliance's exterior and secures the control buttons and display assembly. It gives worn, cracked, or faded console areas a like-new appearance and protects internal controls from damage. What it does

• Replaces a cracked, broken or cosmetically damaged console front to restore appearance
• Protects the underlying control board, switches and display from spills and debris
• Provides the mounting surface for buttons, knobs and the display assembly
• Commonly needed when buttons stick, the console is split, or the front is warped

• One control-console front panel

• Disconnect power (unplug or switch off breaker) before beginning any repair
• Remove trim and control housing fasteners to access the old panel; keep existing screws and brackets
• Handle edges carefully to avoid cuts and prevent damage to the new panel or attached wiring
• Transfer components exactly as removed and verify connections before reassembly

A small 3mm x 8mm fastener used to secure panels, brackets, and small components. Replacing a missing or damaged screw helps restore proper fit and reduces vibration or loose parts. What it does:

• Secures trim, panels, brackets or small component mounts.
• Keeps parts aligned so doors and panels fit correctly.
• Stops rattling or vibration caused by loose hardware.
• Useful when a screw is stripped, missing, or damaged.

• Disconnect power or unplug the appliance before you service it.
• Use the correct screwdriver or bit to avoid stripping the head.
• Thread the screw in by hand first, then snug—do not overtighten.
• Keep small parts away from children and dispose of old fasteners properly.

This is a genuine mounting screw used to secure appliance components and panels for a safe, stable fit. It replaces a lost or damaged fastener to restore proper alignment and reduce rattles or loose trim. What it does:

• Secures panels, trim, brackets or small assemblies to the appliance frame
• Prevents vibration-related noise and loose or sagging parts
• Restores proper fit after repair or disassembly
• Useful when the original screw is stripped, missing, or broken

• One mounting screw

• Use the correct screwdriver or bit to avoid stripping the head
• Power off and unplug the appliance before servicing when applicable
• Keep removed hardware organized to ensure correct reassembly
• If threads are damaged, replace with the specified OEM screw only

This door latch spring restores the return tension in your microwave's door release mechanism so the latch engages and releases correctly. Replacing a fatigued or broken spring helps ensure safe door operation and reliable interlock switch activation.

• Provides the return force for the latch lever/door release button
• Helps door hooks engage fully and release smoothly
• Supports proper interlock switch actuation so the unit will run only when the door is closed
• Typical failure signs: door won't latch, "open/close door" error, door button sticks, or needing to hold the door shut to start

• Disconnect power. Microwaves can retain dangerous high voltage even when unplugged; discharge the capacitor
• Access the latch assembly behind the control panel; note the spring's orientation and attachment points
• Use needle-nose pliers to install without overstretching; inspect the latch lever and door hooks for wear
• Verify proper door closure and interlock switch operation before reassembly

This replacement frame restores the appliance's outer trim and helps hold the control/door area together for a clean, finished appearance. It's a direct-fit exterior trim piece that replaces damaged or worn frames. What it does:

• Replaces a cracked, chipped, warped or bent trim/frame that affects appearance
• Secures and aligns the surrounding control or door components to reduce gaps and rattles
• Covers internal edges to help keep out dust, moisture and debris
• Restores the original look after impact or wear

• Disconnect power to the appliance before starting any repair
• Remove required trim, screws or clips to access and replace the frame; keep fasteners for reuse unless damaged
• Handle edges carefully—trim pieces can be sharp; use proper hand protection

This replacement hardware mounting fastener secures panels, doors or trim on select Frigidaire appliances to restore stable attachment and reduce vibration. It's a direct-replacement style component used where factory fasteners have worn or been lost. What it does:

• Secures appliance panels, trim pieces, doors or drawers to the cabinet or frame
• Restores proper alignment and reduces rattling or vibration noises
• Prevents loose parts that can catch or rub during operation
• Helps maintain a tight seal and smooth operation of moving components

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Use the correct-size screwdriver or socket; avoid overtightening which can strip threads or damage trim
• Keep removed fasteners and small parts contained to prevent loss during reassembly
• Replace all matching pieces for even fit and alignment

This is a replacement mounting screw used to secure panels, trim, and small components in compatible appliances. Installing the correct screw restores a secure fit and helps stop rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces or small assemblies to the appliance frame
• Prevents parts from shifting, vibrating, or producing rattling noises when in place
• Replaces missing, worn, or stripped fasteners that cause loose doors or misaligned trim
• Works with the original mounting points and thread types used by the manufacturer

• Always disconnect power or unplug the appliance before servicing to avoid electrical hazard.
• Use the correct screwdriver or bit to avoid stripping the head; do not overtighten.
• Keep track of small parts and compare the new screw to the old one before installation.

Replacement screw used to secure panels, trim, and internal components in Frigidaire appliances. Restores proper fit after repairs and helps eliminate rattling or loose parts for safer, quieter operation. What it does:

• Secures panels, brackets, and trim to maintain correct alignment and fit
• Prevents vibration and rattling caused by loose or missing fasteners
• Use when original screw is missing, stripped, or damaged
• Matches common fastener locations on affected Frigidaire appliances

• Disconnect power and water before starting any repair
• Use the correct driver to avoid stripping the screw head; hand-start to ensure alignment
• Do not overtighten; tighten until snug to avoid damaging threads or plastic parts

This is a replacement screw used to secure appliance components and panels so assemblies stay stable and aligned. It provides a straightforward fix when a mounting fastener is missing, stripped, or damaged. What it does

• Secures panels, brackets, or trim to prevent movement and vibration
• Stops rattling or loose parts caused by missing or damaged screws
• Restores proper fit and alignment of the affected assembly
• Works wherever the OEM-designated screw of this size and thread is required

• Turn power off or unplug the appliance before working on electrical areas
• Use the proper-size driver to avoid stripping the head
• Start threads by hand, then tighten until snug — do not overtighten
• If the original screw is corroded or the hole is damaged, inspect mating parts for repair before installing