Parts for Electrolux EI30BM5CHBB: 05 - Control Panel / Door Parts

This main electronic control manages refrigerator functions and user settings, restoring programmed cooling cycles and display/control responses when the original board fails. Replaces a failed or unresponsive control for cooler operation and interface control. What it does:

• Sends signals to compressor, fans, and defrost system to regulate temperatures
• Interprets user inputs and displays status from the control panel
• Helps correct intermittent or total loss of refrigerator cooling when board is defective
• Can resolve symptoms like unresponsive controls, incorrect temperatures, or no display/output

• One control board

• Unplug the appliance before starting and ensure power remains off while working
• Handle the board by its edges and avoid static discharge; use an anti-static wrist strap if available
• Compare new board to the old one and transfer any brackets or connectors as needed
• Reinstall all fasteners and restore power, then verify operation of controls and cooling

Replacement grille frame for your microwave. Snaps into place and secures with screws. Order a new one if yours is cracked, broken, or missing.

Fix a blank or flickering microwave display with this control board. Restores digital readout and touch controls. Moderate DIY repair, 30-45 minutes.

Replacement front panel for microwave control console. Restores worn, cracked, or faded exterior and secures control buttons and display assembly.

3mm x 8mm screw secures trim, panels, and brackets inside your microwave. Replace missing or stripped screws to restore proper fit and alignment.

Mounting screw for microwave panels, trim, and brackets. Replaces lost or damaged fasteners to restore secure alignment and eliminate rattles or loose components.

Replacement spring for microwave door latch mechanism. Restores return tension so the latch engages and releases correctly. Needed when spring is broken or worn.

Replacement trim frame for microwave door and control area. Restores outer appearance when original is cracked, chipped, warped, or bent. Direct-fit part.

Microwave door seal creates airtight closure for safe operation. Replace if torn, cracked, or loose to prevent microwave leaks. Verify fit with your model.

Microwave mounting screw used to secure internal components or attach the unit to cabinets. Replace if screw is stripped, missing, or broken.

Replacement washer for your microwave. Installs between components to provide spacing or cushioning. Order a new one if the original is missing, worn, or damaged.

A replacement unified-thread screw used to secure appliance panels and internal components. Provides a direct fastener to restore secure attachment when original screws are missing, damaged, or corroded. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components that use a unified-thread screw.
• Restores secure mounting to reduce rattling, movement, or misalignment of parts.
• Replaces stripped, rusted, or missing screws to help maintain safe operation.
• Works where the appliance's service manual or parts diagram specifies a unified-thread fastening point.

• Disconnect power and water before servicing for safety.
• Use the correct screwdriver or bit to avoid stripping the head; install by hand until started, then snug—do not overtighten.
• Replace like-for-like: match thread type and length to the removed screw to ensure proper fit and function.
• If other fasteners show corrosion or damage, inspect nearby hardware and replace as needed.

Hardware kit for mounting microwave to wall and cabinet. Includes screws, bolts, and washers for secure installation. Replaces lost or missing fasteners.

Replacement owner's manual and care guide for your microwave. Includes operating instructions, maintenance tips, and warranty information.

Wire rack for microwave ovens. Installs inside the cavity to provide an elevated cooking surface. Replace if bent, rusted, or missing from your unit.

Replacement wiring harness for microwaves. Connects electrical components inside the unit. Order if your harness is damaged, frayed, or melted.

Replacement mounting screw secures panels, trim, and components in microwaves. Needed when original screws are stripped, missing, or lost during repairs.

Replacement mounting screw that secures panels, trim, and internal components in microwaves and wall ovens. Needed when screws are stripped, missing, or lost.

This is a replacement screw used to secure appliance components and panels so assemblies stay stable and aligned. It provides a straightforward fix when a mounting fastener is missing, stripped, or damaged. What it does

• Secures panels, brackets, or trim to prevent movement and vibration
• Stops rattling or loose parts caused by missing or damaged screws
• Restores proper fit and alignment of the affected assembly
• Works wherever the OEM-designated screw of this size and thread is required

• Turn power off or unplug the appliance before working on electrical areas
• Use the proper-size driver to avoid stripping the head
• Start threads by hand, then tighten until snug — do not overtighten
• If the original screw is corroded or the hole is damaged, inspect mating parts for repair before installing

This is a factory-style adhesive replacement label that restores original markings, warnings, and identification on the appliance. It helps keep important model/serial and safety information legible for service and ownership. What it does:

• Restores factory-applied markings, identification, and safety/instruction text
• Makes model/serial and wiring/installation info readable for service techs
• Replaces labels that are faded, torn, or missing, improving safety and documentation
• Non-electrical part — purely informational/identification function

• One adhesive appliance label as pictured

• Clean and dry the mounting surface; remove oils or residue for best adhesion
• Peel backing and align carefully before pressing firmly to set the label
• Avoid repositioning once applied to prevent damage; allow adhesive to cure before heavy cleaning
• No electrical disconnection required for label replacement, but follow appliance safety guidelines