Parts for Frigidaire CGMV173KWC: 05 - Control Panel,Door,Miscellaneous Parts

Fix turntable running on its own, flashing lights, or blank display. This electronic control board manages your microwave's interface and functions.

3mm x 8mm screw secures trim, panels, and brackets inside your microwave. Replace missing or stripped screws to restore proper fit and alignment.

Complete microwave door assembly that attaches to the front of your microwave. Replace if your door is cracked, damaged, or no longer seals properly.

Microwave won't start or light stays on when door closes? A faulty door latch prevents proper switch engagement. DIY repair typically takes 15-20 minutes.

Replacement spring for microwave door latch mechanism. Restores return tension so the latch engages and releases correctly. Needed when spring is broken or worn.

A protective cover that helps contain microwave radiation around the door seal area for safety. Located inside the microwave door frame along the edges. Replace if you notice visible damage, warping, or gaps that could allow microwave leakage during operation.

Mounting screw for microwave installation and assembly. Replaces lost, stripped, or damaged screws that secure panels, brackets, or components.

Replacement mounting screw for microwave installation and assembly. Used to secure panels, brackets, or components. Order if original is missing or stripped.

Hardware kit for mounting microwave to wall and cabinet. Includes screws, bolts, and washers for secure installation. Replaces lost or missing fasteners.

A replacement unified-thread screw used to secure appliance panels and internal components. Provides a direct fastener to restore secure attachment when original screws are missing, damaged, or corroded. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components that use a unified-thread screw.
• Restores secure mounting to reduce rattling, movement, or misalignment of parts.
• Replaces stripped, rusted, or missing screws to help maintain safe operation.
• Works where the appliance's service manual or parts diagram specifies a unified-thread fastening point.

• Disconnect power and water before servicing for safety.
• Use the correct screwdriver or bit to avoid stripping the head; install by hand until started, then snug—do not overtighten.
• Replace like-for-like: match thread type and length to the removed screw to ensure proper fit and function.
• If other fasteners show corrosion or damage, inspect nearby hardware and replace as needed.

Microwave mounting screw used to secure internal components or attach the unit to cabinets. Replace if screw is stripped, missing, or broken.

Replacement washer for your microwave. Installs between components to provide spacing or cushioning. Order a new one if the original is missing, worn, or damaged.

Cosmetic badge that attaches to the microwave exterior. Replaces a cracked, faded, or missing badge to restore the original branded appearance.

Replace your microwave's cracked or broken door glass panel. This clear viewing window installs in the door assembly for safe visibility during cooking.

This small replacement cap protects and seals appliance openings or fittings to prevent debris, moisture, or accidental contact. It restores a finished appearance and helps maintain part function by keeping contaminants out of sensitive areas. What it does:

• Covers exposed fittings, ports, or fasteners to keep out dust and moisture
• Protects nearby components from accidental contact and wear
• Helps maintain proper sealing for adjacent parts and reduces risk of leaks
• Restores OEM appearance for a clean finish

• One replacement cap

• Inspect the mating surface for damage or residue and clean before installing
• Press the cap into place until fully seated; no special tools usually required
• Replace if cracked, warped, or no longer fits securely
• Disconnect power and shut off water before servicing nearby components

Mounting screw for microwave panels, trim, and brackets. Replaces lost or damaged fasteners to restore secure alignment and eliminate rattles or loose components.

This access panel cover replaces a damaged or missing exterior cover to protect internal components and restore the appliance's finished appearance. It helps keep electrical parts and wiring shielded while improving safety and looks. What it does

• Protects internal components from dust, debris and accidental contact
• Restores the appliance's exterior finish for a clean appearance
• Helps prevent exposure of wiring and connectors that could cause safety concerns
• Fits into the existing mounting points or clips for a secure fit

• One access panel cover

• Disconnect power to the appliance before beginning any work
• Remove any adjacent trim or fasteners to access the mounting points; a screwdriver or nut driver may be needed
• Align cover with existing clips or screw holes and secure without forcing to avoid breaking tabs
• Replace damaged clips or fasteners before installing the cover

This is a factory-style adhesive replacement label that restores original markings, warnings, and identification on the appliance. It helps keep important model/serial and safety information legible for service and ownership. What it does:

• Restores factory-applied markings, identification, and safety/instruction text
• Makes model/serial and wiring/installation info readable for service techs
• Replaces labels that are faded, torn, or missing, improving safety and documentation
• Non-electrical part — purely informational/identification function

• One adhesive appliance label as pictured

• Clean and dry the mounting surface; remove oils or residue for best adhesion
• Peel backing and align carefully before pressing firmly to set the label
• Avoid repositioning once applied to prevent damage; allow adhesive to cure before heavy cleaning
• No electrical disconnection required for label replacement, but follow appliance safety guidelines