Parts for Bosch HBL5651UC/01: Control Panel Parts

This replacement switch restores reliable on/off signaling for the function it controls in your appliance. A worn or sticking switch can cause intermittent response or complete failure of the feature it's meant to operate.

• Converts mechanical input into an electrical on/off signal for a linked component or control
• Common signs of failure: function won't start or respond, intermittent operation, or needing extra pressure/wiggling to work
• Replaces a damaged, heat-worn, or stuck original to restore consistent performance

• Disconnect power at the breaker or unplug the appliance before servicing; shut off other utilities as applicable
• Photograph and label wires; transfer leads to the new switch one at a time to avoid miswiring
• Match actuator orientation to the original; secure mounting without overtightening and avoid bending terminals
• Restore power and test operation before final reassembly

This replacement switch restores reliable on/off control for the designated function in your appliance. Worn contacts can cause a feature to stop responding or work intermittently, disrupting normal operation.

• Opens and closes the electrical circuit to the assigned component as designed by the manufacturer
• Ensures consistent activation and deactivation of the controlled function
• Common symptoms: no response when pressed, intermittent operation, or needing to hold/jiggle to engage
• Can be checked with a continuity test when power is disconnected

• Disconnect power at the breaker or unplug the appliance before servicing; allow any hot surfaces to cool
• Access the switch location; remove any panels/knobs as required
• Photograph and transfer wire positions one at a time; ensure fully seated, secure connections
• Mount the new switch firmly and verify proper operation before final reassembly

This display module is the electronic user-interface board behind the control panel. It lights the display and reads button inputs so you can select cycles and see status when the original board fails.

• Drives the front-panel display to show time, options, and cycle status
• Interprets keypad or touch inputs and relays commands to the appliance's main control
• Communicates with the power/control module to execute selected settings
• Typical failure symptoms: blank or dim display, missing segments, flickering readout, or an unresponsive control panel

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use anti-static protection and handle the board by its edges
• Access from behind the control panel; photograph wiring and move one connector at a time
• Ensure ribbon cables and plugs are fully seated; transfer any fascia/overlay from the old board if applicable

This facia panel is the exterior trim that covers and protects the appliance control area, restoring a clean, finished look and shielding buttons and electronics from spills and everyday wear. Ideal for replacing cracked, scratched, or damaged front trim. What it does:

• Protects the control buttons and electronics from moisture, grease, and impact
• Restores the appliance's finished appearance after cosmetic damage or wear
• Helps keep control labels and touch points readable and intact
• Prevents debris from entering the control cavity, reducing risk of malfunction

• Disconnect power to the appliance before starting any repair
• Remove the outer door or access trim per the service manual to reach mounting fasteners
• Handle carefully to avoid scratching the new panel; plastic trim can crack if forced

This is a replacement mounting screw used to secure appliance panels and components. It restores proper fit and prevents rattling or loose parts so the appliance operates quietly and safely. What it does:

• Secures panels, brackets, or components to the appliance frame
• Prevents vibration-related noise and loose-fitting parts
• Replaces missing or damaged screws that can cause misalignment
• Helps maintain safe cabinet and component attachment during operation

• Use the matching screw hole and thread orientation; do not force if fit is not smooth
• Tighten until snug—avoid over-tightening to prevent stripping or damage
• Disconnect power and follow appliance-specific safety procedures before servicing
• Inspect surrounding fasteners and mounts for wear

The Oven Knob is an OEM part for Bosch wall ovens. This knob attaches to the oven control shaft to allow for adjustment of temperature settings and operation of other functions like the oven timer.

Causes may include repeating twisting motions over time compromising the knob's structure or a single impact event resulting in cosmetic or functional damage.

Symptoms of a bad oven knob include:

• Difficulty turning or grabbing onto the knob surface
• Loose, wobbly or detached knob that cannot securely set oven functions
• Cracked, worn or discolored knob lacking clear indicator markings

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.