Parts for Frigidaire FEB786CESG: 02 - Control Panel Parts

This part has been discontinued and is no longer available.

This vent trim is the molded plastic exterior piece that covers and directs airflow at the refrigerator vent opening, restoring the appliance's finished appearance and proper airflow path. What it does

• Covers the vent opening to help direct cooled air into the fresh food compartment.
• Replaces cracked, broken or missing trim that causes drafts or looks unsightly.
• Helps maintain an even appearance along the refrigerator front and prevents small objects from entering the vent.
• Fits into the existing vent opening and secures with clips or screws depending on model.

• Disconnect power to the appliance or unplug the refrigerator before starting.
• Remove any mounting screws or gently release retaining clips; align the trim and snap or screw it into place without forcing.
• If clips or fasteners are damaged, replace them before completing installation to ensure a secure fit.
• Use basic hand tools; avoid sharp tools that could scratch surrounding surfaces.

Motor making noise or loose? This motor mounting nut secures motors in refrigerators, ranges, and other appliances. Simple install takes 15 minutes.

Split lockwasher secures screws and bolts in your oven. Replace if missing, damaged, or worn to maintain stable panel and component connections.

This 10-16 x 1-1/4 screw secures appliance panels and components, restoring proper fit and preventing loose parts. Use it when fasteners are missing, stripped, or causing rattle and misalignment. What it does:

• Fastens trim, brackets, or interior panels to restore secure attachment
• Stops rattling or vibration caused by loose hardware
• Replaces missing or damaged screws to maintain safe operation
• Matches OEM thread and length for correct fit in specified locations

• Disconnect power and empty appliance as needed before servicing
• Use the correct screwdriver or bit to avoid cam-out or head damage
• Do not overtighten; snug until parts seat to prevent striping or cracking
• Replace all matching screws for consistent fit

This black washer is a small replacement fastener washer used on compatible Frigidaire laundry appliances to restore proper spacing and reduce metal-on-metal contact. It helps maintain component alignment and smooth operation. What it does:

• Provides a durable spacer between fastened parts to prevent wear and abrasion
• Helps reduce noise and vibration caused by loose or worn hardware
• Restores correct clearance for rotating or moving components
• Commonly replaced when original washer is corroded, deformed, or missing

• Disconnect power and water to the appliance before servicing
• Install in the same orientation as the original; reuse compatible fasteners only

Flat washer used to secure components in washers, dryers, and laundry centers. Replace if washer is missing, bent, or corroded during repairs.

Oval-head square-drive screw secures interior and exterior oven panels, brackets, and trim. Replace worn, stripped, or missing screws for secure assembly.

Mounting screw secures heating element to cooktop surface. Replace if stripped, rusted, or missing to ensure proper element installation and stability.

Replaces the electrical junction box and pre-wired harness in your oven. Needed when the box is cracked, damaged, or wiring connections are worn or loose.

Positions and supports range components to maintain proper alignment. Replace if cracked, broken, or missing to prevent rubbing and ensure panels fit correctly.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Specs: 8 - 18 x 0.500

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment