Parts for Frigidaire FFET3025PBC: 03 - Control Panel Parts

This replacement cover restores the appliance's exterior and protects internal components from dust and damage. It replaces a worn or missing access panel to keep the unit looking finished and functioning safely. What it does:

• Covers and protects internal components, wiring and connectors from debris and accidental contact
• Restores the appliance's finished appearance by replacing a cracked, dented or missing panel
• Helps reduce vibration noise and keeps internal parts secured in place
• Commonly used when the old cover is damaged, loose, or causing rattling

• Always unplug the appliance or disconnect power at the breaker before starting repairs
• Use basic hand tools to remove fasteners; keep removed hardware for reinstallation
• Handle edges carefully—metal or plastic panels can have sharp edges

This electronic control board regulates oven functions, clock, and timer for precise cooking control and user interface operation. It replaces a failed board to restore display readouts and control responsiveness. What it does:

• Manages oven temperature setpoints, bake/broil cycles and timed cooking functions
• Powers and displays clock, timer and control panel buttons
• Replaces a non-responsive or blank control display to restore normal oven operation
• Helps address intermittent control errors, display glitches or inability to start timed cycles

• One electronic control board

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Handle the board by edges and avoid touching components to prevent ESD damage
• Verify wiring connections and thermostat/element operation before installing replacement

This OEM replacement part is a relay control board for ovens. The relay control board receives signals from the main oven control board. This part regulates the oven's temperature. If the oven is no longer heating properly or maintaining temperature it might be time to replace the relay control board. Luckily replacing this board is an easy repair. To replace the relay control board, begin by turning off all power to the oven. Once the power has been shut, move the oven away from the wall to gain access to the upper back panel. Remove the panel and locate the relay control board. Snap it out of its mounting brackets and remove the wire harness connected to it. Reinsert the wire connectors to the new relay board in the correct order. Secure the new board into its mounting brackets. Reinstall the upper back panel.This genuine replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.