Parts for Frigidaire FGB557CESE: 02 - Control Panel Parts

This is a satin-finish trim piece that fits along the splasher area of a range or oven. It provides a finished appearance and helps protect the edge where the cooktop meets the backsplash. Replace this trim if it is dented, discolored, corroded, or missing, which can detract from the appliance's appearance and leave edges exposed.

This clock mounting bracket secures the oven/range clock assembly to the control panel so the timer and clock stay properly aligned and supported. It replaces a bent, broken or missing bracket to restore stable clock placement and control-panel fit. What it does:

• Provides a secure mounting point for the range/oven clock or control-timer module
• Keeps the clock/timer aligned so buttons and display sit flush with the control panel
• Prevents rattling or movement that can cause display/connectivity issues
• Helps maintain correct spacing to avoid interference with adjacent controls

• High-level replacement: remove the control panel or trim to access and swap the bracket; follow your model's service instructions
• Turn off power to the appliance at the breaker before servicing to avoid electrical shock
• Keep fasteners and surrounding parts organized during reassembly; test the clock/timer function after installation
• If plastic clips or screws are damaged, replace them with OEM equivalents for a secure fit

Cork and rubber spacer for ovens and ranges. Provides cushioning and spacing between components. Replace if worn, cracked, compressed, or missing.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Replacement mounting screw that secures panels, trim, and components in ranges and ovens. Needed when original screws are lost, stripped, or damaged.

This part has been discontinued by the manufacturer and is no longer available.

Rubber bumper that cushions the range door or drawer when closing. Replace if cracked, worn, or missing to prevent rattling and protect surfaces.

10-24 x 1/2 inch machine screw that secures temperature probe and thermistor brackets to cooktop, oven, and range chassis. Replace if missing or stripped.

Hex washer head ,10-32 x 0.375. Ground

Cork and rubber spacer for ovens and ranges. Provides cushioning and spacing between components. Replace if worn, cracked, compressed, or missing.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Mounting screw for ranges, ovens, and cooktops. Secures panels, brackets, or internal components. Replace if missing, stripped, or damaged.

Adhesive seal tape restores tight door seals on ovens, reducing air leaks and improving temperature control. Replace when worn or damaged. Confirm fit.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

Replacement mounting screw that secures panels, trim, and components in ranges and ovens. Needed when original screws are lost, stripped, or damaged.