Parts for Frigidaire FGEW2766UDA: Control Panel Parts

This main console control panel houses the oven/range user interface and display, letting you select cooking modes, set temperatures and timers. Replacing a damaged or unresponsive panel restores normal control and feedback. What it does

• Provides the push-button/touch interface and display for oven and cook functions
• Registers user inputs for bake, broil, timer, clock and other controls
• Displays time, temperature and error/status messages
• Stops working or shows blank/garbled display when the panel or internal electronics fail

• One control panel assembly (main console)

• Disconnect power at the breaker or appliance plug before starting work
• Handle the panel and display area carefully to avoid damaging the glass/overlay
• Basic hand tools are typically required; follow OEM instructions for connector and bracket removal
• If the display needs calibration or clock reset after install, refer to the owner's manual

This electronic oven control board is the brain of your range or wall oven. Replacing a failed board restores the display and keypad response and allows the appliance to heat and run bake/broil cycles reliably again.

• Controls relays for bake and broil circuits
• Uses oven sensor feedback to regulate and maintain temperature
• Powers the time/temperature display and reads keypad inputs
• Common symptoms: blank or erratic display, unresponsive buttons, F-code errors, oven won't heat or shuts off mid-cycle

• Disconnect power at the breaker before servicing; allow the appliance to cool
• Static-sensitive component—handle by the edges and avoid touching circuitry
• Note/photograph wire locations; transfer connectors one at a time to the new board
• Mount the board in the control panel, secure connections, restore power, and test

Specs: 8 x 0.750

This wire harness routes power and signals between the appliance's controls and components to restore reliable electrical connections and proper function. Use the correct harness to replace damaged, corroded, or broken wiring assemblies. What it does:

• Connects control boards, switches, motors, and sensors so parts receive power and communicate
• Replaces frayed, pinched, or open wires that can cause intermittent operation
• Helps stop failures like no power to components, unresponsive controls, or parts that won't run
• Maintains factory routing and connector fit for safe, reliable operation

• Disconnect power (unplug or shut off breaker) before starting any repair
• Handle connectors gently; match keyed plugs and secure all retaining clips
• Route harness to avoid sharp edges, heat sources, and moving parts

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.