Parts for Frigidaire FPEW3077RFA: 02 - Control Panel Parts

This shield is a small protective trim piece used on select Frigidaire appliances to cover and protect openings and mounting areas from debris and wear. It helps maintain proper airflow and keeps internal components shielded. What it does:

• Covers exposed openings or fasteners to prevent debris buildup and reduce wear
• Helps direct airflow and protect seals or insulation from damage
• Reduces the chance of contact with moving or hot components
• Commonly replaced when cracked, warped, or missing

• Designed for a simple replacement; usually secured with screws or snap-fit tabs
• Turn off and unplug the appliance before servicing
• Handle gently to avoid bending tabs; align mounting holes before fastening

This replacement shield is a molded protective cover that shields internal components from debris and directs airflow for reliable operation. It restores proper component protection and helps reduce noise from loose or damaged covers. What it does

• Protects wiring, sensors, and nearby components from contact, dirt, and debris
• Helps maintain correct airflow routing around internal parts
• Reduces rattles or vibration noises caused by a broken or loose shield
• Prevents accidental contact with moving or hot parts during use

• One replacement shield

• Disconnect power before attempting any service to avoid shock or injury
• Inspect mounting tabs and fasteners; replace any damaged clips for secure fit
• Use basic hand tools; avoid forcing the part to prevent breakage

This door switch detects when the appliance door is opened or closed and sends the signal to control lights or functions, restoring normal operation and safety. Ideal when lights won't turn on or cycles don't start. What it does:

• Opens and closes an electrical circuit when the door is ajar or shut
• Commonly used to turn interior lights on/off or enable control features
• Designed as a direct-fit replacement when the original door switch is faulty

• One replacement door switch

• Disconnect power before servicing to avoid shock or damage
• Access may require removing door trim or panel—refer to your model's service guide
• Handle terminals carefully; confirm connector orientation before reconnecting

This potentiometer is the user control variable resistor that lets the appliance vary a setting (speed, temperature or timer) from the front control panel. Replacing a faulty potentiometer restores responsive, smooth control. What it does:

• Converts knob rotation into an adjustable electrical signal for the appliance control
• Restores consistent setting changes when knob rotation previously produced no response
• Eliminates erratic or jumpy adjustments caused by worn or dirty contacts
• Used wherever a variable user input is required (e.g., temperature, speed, or timer control)

• Disconnect power to the appliance before starting any repair to avoid shock
• Access usually requires removing the control panel or console; keep track of screws and fasteners
• Note and label any wiring connections before disconnecting for correct reassembly

This control panel console assembly houses the oven/range touch controls and display so you can set cook modes, temperatures and timers. It restores user input and status feedback when the original panel is cracked, unresponsive, or showing no display. What it does:

• Replaces the front control interface that registers touchpad or keypad inputs.
• Provides the display and indicator lights that show temperature, time, and oven status.
• Commonly used when buttons stop responding, the display is blank, or controls work intermittently.
• Interfaces with the range/oven's electronic control to start bake, broil, timer, and other functions.

• Disconnect power to the appliance before removing the old panel—risk of shock.
• Handle the panel carefully to avoid damaging the display or wiring harness.
• Follow factory service instructions for removing trim and accessing mounting screws; do not force connectors.

The Indicator Light Lens is an OEM part for Frigidaire ranges. This component covers and protects the indicator light, which signals when a burner or the oven is on, providing a visual cue for users to ensure safe operation.

Over time, the indicator light lens can become damaged or discolored due to heat exposure, regular cleaning, or accidental impacts. Causes of a bad indicator light lens include cracking, warping, or clouding that obscures the light.

Symptoms of a bad indicator light lens include:

• The indicator light not being clearly visible
• Cracks or breaks in the lens
• Discoloration or cloudiness that diminishes the brightness of the light
• The lens becoming loose or falling off

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This interior light lamp assembly provides illumination inside the appliance so you can see contents clearly. It replaces a burned or damaged refrigerator/freezer interior lamp to restore usable lighting. What it does:

• Houses and secures the interior bulb to provide cabinet illumination
• Replaces a cracked, discolored, or non-functioning light assembly
• Helps stop flickering or intermittent lighting when the original unit is faulty
• Works with the existing bulb and wiring harness to restore normal light operation

• Disconnect power to the appliance before replacing the lamp to avoid electric shock
• Handle the lens and bulb carefully; wear gloves to avoid fingerprints on bulbs if replacing
• Check bulb type and socket condition; replace bulb separately
• If wiring or mounting clips are damaged, inspect and replace those components as needed

This interior refrigerator light bulb provides the lamp needed to illuminate the fresh food compartment, making it easier to find items when the door is open. It replaces a burnt or dim interior lamp to restore visibility. What it does:

• Replaces the refrigerator's interior lamp so the compartment lights when the door opens
• Restores normal brightness for safer, easier access to food and containers
• Common symptom: no light or a dim light when the door is opened
• Fits into the existing lamp socket and works with the existing lens or cover

• Disconnect power to the appliance before servicing to prevent shock
• Allow a recently used bulb to cool before removing to avoid burns
• Remove the lamp cover, then pull or twist the old bulb out and install the replacement
• Handle the bulb with a cloth or gloves; avoid getting oils from skin on the bulb surface

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

This electronic oven control board is the brain of your range or wall oven. Replacing a failed board restores the display and keypad response and allows the appliance to heat and run bake/broil cycles reliably again.

• Controls relays for bake and broil circuits
• Uses oven sensor feedback to regulate and maintain temperature
• Powers the time/temperature display and reads keypad inputs
• Common symptoms: blank or erratic display, unresponsive buttons, F-code errors, oven won't heat or shuts off mid-cycle

• Disconnect power at the breaker before servicing; allow the appliance to cool
• Static-sensitive component—handle by the edges and avoid touching circuitry
• Note/photograph wire locations; transfer connectors one at a time to the new board
• Mount the board in the control panel, secure connections, restore power, and test

This electronic control assembly replaces a faulty oven control to restore bake, broil and timer functions. It provides the user interface and electronic control logic so the range responds correctly to temperature and cooking commands. What it does:

• Controls oven heating cycles, timers and user inputs through the front control interface
• Manages bake/broil elements and maintains commanded oven temperature via electronic relay signals
• Commonly replaced for symptoms such as unresponsive control pad, incorrect oven cycles, or display errors
• Works as the main electronic control when diagnostics point to a failed control board

• Disconnect power to the appliance before starting—risk of electric shock.
• Access usually requires removing the control panel; keep screws and fasteners organized.
• Handle the control assembly carefully to avoid damage to the display and connectors.

Specs: 8 x 0.750

This wiring harness connects and routes power and signals between appliance components, restoring reliable electrical connections and resolving intermittent or non-working circuits. It's a direct-fit replacement designed to match OEM wiring layouts. What it does:

• Replaces worn or damaged wiring to restore power and signal paths
• Helps fix intermittent operation, components not receiving power, or burned/shorted wiring symptoms
• Maintains correct plug/connector locations and wire lengths for proper fit
• Keeps control and component circuits isolated and organized to prevent shorts

• One complete wiring harness assembly with factory-style connectors

• Disconnect power before starting any repair to avoid shock or injury
• Handle connectors by the housings; do not pull on individual wires
• Route harness following original wire clips and mounting points for secure fit
• If connectors are corroded or terminals are damaged, replace them before reassembly

This wiring harness routes power and signals between components so your appliance operates reliably. It replaces a damaged or burned harness to restore electrical connections and reduce intermittent power or control failures. What it does:

• Reconnects power and control circuits between major components
• Restores reliable electrical contact if original wires are frayed, melted, or broken
• Helps stop intermittent operation, no-heat or non-start symptoms caused by wiring faults
• Provides factory-style terminals and routing to match original wiring layout

• One wiring harness with factory-style connectors and pre-terminated leads

• Disconnect power at the household breaker or unplug the appliance before starting
• Compare the replacement harness to the original to confirm connector type and lead lengths
• Secure wiring away from sharp edges, moving parts, and heat sources during installation

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.