Parts for Ge C2Y366P3M1D1: Control Panel Parts

This glass display is the replacement front glass for the appliance control panel. It restores a clean, readable surface for the controls and protects the underlying electronics from spills and debris. What it does:

• Replaces cracked, scratched, or chipped control panel glass to improve appearance and readability
• Protects the control board and touch/button assembly from spills, grease, and light impact
• Helps maintain proper user interaction with the oven/range controls when the original glass is damaged
• Matches the OEM shape and mounting points for a like-for-like fit when installed

• Disconnect power (unplug or shut off circuit breaker) before starting any work
• Remove control console trim and any fasteners carefully to avoid chipping the glass
• Handle glass edges with caution; wear cut-resistant gloves and eye protection

This control bracket secures the appliance control assembly to the cabinet, helping keep buttons, knobs, and the control board properly aligned for reliable operation. Designed to restore stable control-panel mounting after damage or wear. What it does

• Holds the control/module assembly in the correct position so front controls operate smoothly
• Prevents excessive movement or vibration that can cause intermittent button or knob issues
• Restores proper alignment after a broken or bent mounting tab
• Helps maintain electrical connections by stabilizing the control module

• Designed to replace a broken or bent bracket; inspect surrounding clips and fasteners for damage before installing
• Power off and unplug the appliance before attempting removal or installation to avoid shock
• Typical installation requires removing the control panel or console—retain screws and grounding hardware
• Handle the board carefully to avoid static discharge or connector damage

This encoder assembly senses control-knob position and converts rotations into electronic signals for the range/oven control board, restoring accurate input and helping the control respond correctly to knob adjustments. What it does:

• Converts knob rotation into digital signals the control board uses to change settings.
• Replaces a worn or damaged encoder that can cause unresponsive or inconsistent control inputs.
• Commonly linked to symptoms like controls not changing settings, intermittent response, or incorrect selection tracking.
• Works with the console/control board to ensure knob position is detected reliably.

• Disconnect power to the appliance at the breaker before starting any work.
• Access usually requires removing the console or control panel; keep track of fasteners and any small brackets.
• Handle the encoder and any attached harness or ribbon carefully to avoid damage; align the shaft properly when seating the part.
• After installation, restore power and verify control responsiveness.

This wiring harness provides the factory-style electrical connections between the appliance control and its components, restoring reliable signal and power routing for proper operation. What it does:

• Routes power and control signals between the main control and connected components
• Replaces damaged, frayed, or corroded wiring that can cause intermittent operation
• Helps stop symptoms like components not powering on, intermittent cycles, or blown fuses
• Restores secure connector mating to reduce arcing and poor contacts

• One factory-style wiring harness with attached connectors as shown

• Disconnect all power (unplug or shut off breaker) before starting work
• Compare the part to the original to confirm connector types and wire lengths before installing
• Route and secure the harness following the appliance's wiring channels; avoid contact with sharp edges or moving parts

This is a stainless-steel machine screw used to secure components in appliances. Its #8-18 thread and 3/8" length provide a reliable, corrosion-resistant fastening where a short machine screw is required. What it does:

• Fastens panels, brackets, or small assemblies with a #8-18 threaded hole
• Resists rust and corrosion in humid appliance compartments
• Provides a short, secure hold where space is limited
• Compatible with standard #2 Phillips or compatible driver bit for installation

• Power off and unplug the appliance before servicing
• Use the correct driver to avoid stripping the head
• Do not overtighten; stop when snug to avoid thread or component damage
• If replacing multiple fasteners, reuse only the same size and type

This electronic control and display assembly replaces a failed oven control so you can use the clock, touchpad and oven functions again. It restores the user interface and command signals between the console and oven controls. What it does

• Provides the clock and digital display for oven settings and timers
• Accepts touchpad/console input to select bake, broil, bake time and other functions
• Sends control commands to the oven's control board and heating elements
• Common symptoms: blank or flickering display, unresponsive touchpad/buttons, or loss of clock/timer functions
• Resolve intermittent control errors or inability to select oven modes when caused by a faulty display module

• One control display module

• Disconnect power at the breaker before starting; electrical shock hazard.
• Handle the module and ribbon/connectors carefully to avoid damage; observe anti-static precautions if available.
• Verify connector seating and secure mounting; do not force connectors.

Size: 8 - 18 ab hxw 5/8 s