Parts for Ge CGY366P3M1D1: Control Panel Parts

This glass display is the replacement front glass for the appliance control panel. It restores a clean, readable surface for the controls and protects the underlying electronics from spills and debris. What it does:

• Replaces cracked, scratched, or chipped control panel glass to improve appearance and readability
• Protects the control board and touch/button assembly from spills, grease, and light impact
• Helps maintain proper user interaction with the oven/range controls when the original glass is damaged
• Matches the OEM shape and mounting points for a like-for-like fit when installed

• Disconnect power (unplug or shut off circuit breaker) before starting any work
• Remove control console trim and any fasteners carefully to avoid chipping the glass
• Handle glass edges with caution; wear cut-resistant gloves and eye protection

This control bracket secures the appliance control assembly to the cabinet, helping keep buttons, knobs, and the control board properly aligned for reliable operation. Designed to restore stable control-panel mounting after damage or wear. What it does

• Holds the control/module assembly in the correct position so front controls operate smoothly
• Prevents excessive movement or vibration that can cause intermittent button or knob issues
• Restores proper alignment after a broken or bent mounting tab
• Helps maintain electrical connections by stabilizing the control module

• Designed to replace a broken or bent bracket; inspect surrounding clips and fasteners for damage before installing
• Power off and unplug the appliance before attempting removal or installation to avoid shock
• Typical installation requires removing the control panel or console—retain screws and grounding hardware
• Handle the board carefully to avoid static discharge or connector damage

The Encoder Assembly is an OEM part for GE gas ranges. It digitally converts analog knob movements into signals to control the gas valve, igniter, and temperature settings. 

Causes of a bad encoder assembly include degradation of internal sensors and switches over time, loose wiring connections, or impacts that cause misalignment.

Symptoms of a bad encoder assembly are:

• Delays or errors when trying to light burners
• Inaccurate flame height and temperature level responses 
• Knobs feel sticky, sluggish or jump between settings
• Error codes indicating control module communication issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models.

This wiring harness provides the factory-style electrical connections between the appliance control and its components, restoring reliable signal and power routing for proper operation. What it does:

• Routes power and control signals between the main control and connected components
• Replaces damaged, frayed, or corroded wiring that can cause intermittent operation
• Helps stop symptoms like components not powering on, intermittent cycles, or blown fuses
• Restores secure connector mating to reduce arcing and poor contacts

• One factory-style wiring harness with attached connectors as shown

• Disconnect all power (unplug or shut off breaker) before starting work
• Compare the part to the original to confirm connector types and wire lengths before installing
• Route and secure the harness following the appliance's wiring channels; avoid contact with sharp edges or moving parts

The Control Display Module is an OEM part for GE gas ranges. It is the central component responsible for controlling and monitoring all functions and settings of the range through an LCD interface. 

Symptoms of a bad control display module include: 

• Blank or unresponsive control display  
• Inability to set or change oven temperatures
• Fault codes or error messages appearing 
• Control keys sticking or not responding properly

Causes of a bad control display module can include circuit board failure, liquid damage, overheating issues, or normal component degradation over time.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This genuine replacement screw secures panels, trim and small components on compatible appliances to restore proper fit and prevent rattling or gaps. Use it when a missing or damaged fastener causes loose or misaligned parts. What it does:

• Fastens panels, bezels, trim pieces and small assemblies to the appliance frame
• Restores secure fit to eliminate rattling, vibration noise or loose trim
• Replaces stripped, rusted or missing screws that prevent proper alignment

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Use the correct screwdriver or driver bit to prevent stripping the head
• Tighten securely but avoid over-torquing; excessive force can strip threads or crack plastics
• Keep removed fasteners organized to ensure correct reassembly

This control panel and rail assembly replaces the user interface and front support rail on compatible ranges and cooktops, restoring secure button/knob operation and a finished front appearance. It provides the mounting surface for the control buttons and display. What it does:

• Replaces the front control surface and support rail so buttons, switches, and the display mount correctly.
• Restores stable button/knob operation and prevents a loose or misaligned control panel.
• Can resolve symptoms such as unresponsive or sticking buttons, physical damage to the control face, or a loose/cracked front rail.
• Serves as the cosmetic front piece for the controls, improving appliance appearance.

• Serviceable by a technician or experienced DIYer; disconnect power before beginning work.
• Use appropriate hand tools; follow OEM disassembly steps to avoid damaging clips or connectors.
• Inspect wiring harnesses and connectors for damage during replacement; replace damaged wiring separately.

This is a stainless-steel machine screw used to secure components in appliances. Its #8-18 thread and 3/8" length provide a reliable, corrosion-resistant fastening where a short machine screw is required. What it does:

• Fastens panels, brackets, or small assemblies with a #8-18 threaded hole
• Resists rust and corrosion in humid appliance compartments
• Provides a short, secure hold where space is limited
• Compatible with standard #2 Phillips or compatible driver bit for installation

• Power off and unplug the appliance before servicing
• Use the correct driver to avoid stripping the head
• Do not overtighten; stop when snug to avoid thread or component damage
• If replacing multiple fasteners, reuse only the same size and type