Parts for Ge GHDS360GF0WW: Control Panel Parts

The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.

Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.

Symptoms of a bad Dryer Wire Tie include:

• Loose or unsecured internal wiring
• Interference with dryer components during operation
• Electrical malfunctions or short circuits
• Wires appearing frayed or damaged due to improper support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Fix a loose or misaligned dryer control panel with this front control assembly bracket. Secures the control board and interface to the front panel.

Rubber grommet for dryers. Installs in cabinet or drum assembly to reduce vibration and secure components. Replace if cracked, worn, or missing.

Replace your washer's broken, cracked, or missing control knob with this rubberized grip selector dial. Installs on the control panel for secure turning.

This knob retainer secures a control knob to its switch/timer shaft, keeping your selections engaged and the knob firmly in place. Replace a worn or missing retainer to restore a solid feel and dependable operation.

• Holds the control knob securely on the switch/timer shaft
• Restores positive engagement when turning the knob
• Common fix for a loose, slipping, wobbly, or falling-off knob
• Helps resolve intermittent selection when the knob doesn't grip the shaft

• Disconnect power before servicing
• Pull off the knob to access the retainer
• Align the new retainer with the shaft and press firmly until fully seated
• Reinstall the dial/knob and verify proper engagement

This screw is a direct-fit fastener used to secure appliance panels and components for stable, rattle-free operation. Replacing a stripped, missing or worn screw restores proper part alignment and prevents vibration or loose trim. What it does:

• Secures panels, trim pieces or small components to the appliance frame
• Prevents rattling or movement caused by missing or loose hardware
• Restores proper alignment for switches, panels or covers
• Works as a replacement for a single lost or damaged mounting screw

• Disconnect power and water before beginning any repair
• Use the correct screwdriver bit to avoid stripping the head
• Start threads by hand, then tighten snugly — avoid over-tightening
• Keep removed hardware in a labeled container to avoid loss

Fix a dryer that won't start or respond to settings. This control board manages temperature and cycle functions. Moderate DIY repair with online guides.

Replace your dryer's start button assembly if it's cracked, broken, or unresponsive. This control panel component houses the push button mechanism.

Replacement control panel cover for your dryer's user interface. Installs over the electronic control board. Order if your cover is cracked or missing.

10-18 hex washer screw for securing panels, trim, brackets, and components in appliances. Replaces lost, stripped, or corroded fasteners.

Replacement logo badge emblem for appliance exterior panels. Restores original appearance when emblem is missing, faded, cracked, or damaged. 1 piece.

A replacement 10-16 shoulder screw (Type A) used to secure appliance components where a shoulder/clearance is required. Restores proper alignment and fastening for panels, brackets, or assemblies that use a shoulder-style fastener. What it does:

• Provides a fixed shoulder to control depth and spacing between parts
• Secures panels, brackets, or moving parts while allowing an exact clearance
• Helps prevent over-driving and protects mating parts from damage
• Commonly used where precise alignment or rotation clearance is needed

• Inspect the mating hole and threads for damage before installing
• Use the correct driver and torque—do not over-tighten to avoid stripping
• Replace with the same screw type and size to maintain proper fit and clearance
• Disconnect power and follow all safety precautions when accessing internal components

Fixes electrical safety issues and grounding problems in dryers. This ground screw secures the ground wire to the chassis for safe discharge. Easy install.