Parts for Ge GHDS365GF1MC: Control Panel Parts

The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.

Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.

Symptoms of a bad Dryer Wire Tie include:

• Loose or unsecured internal wiring
• Interference with dryer components during operation
• Electrical malfunctions or short circuits
• Wires appearing frayed or damaged due to improper support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Restore easy, precise cycle selection with this washer control knob. The rubberized knob replaces a cracked or stripped original so you can securely grip and turn the selector without slipping or wobbling.

• Replaces the washer's main control/selector knob
• Rubberized surface improves grip and control
• Mounts on the D-shaped control shaft to turn the timer/control
• Common symptoms: knob cracked, loose or spinning freely, missing, can't change cycles

• Disconnect power before servicing the appliance
• Pull the old knob straight off; avoid prying against the control panel
• Align the flat on the new knob with the shaft and press until fully seated
• The knob engages the shaft and rotates the control smoothly

This knob retainer secures a control knob to its switch/timer shaft, keeping your selections engaged and the knob firmly in place. Replace a worn or missing retainer to restore a solid feel and dependable operation.

• Holds the control knob securely on the switch/timer shaft
• Restores positive engagement when turning the knob
• Common fix for a loose, slipping, wobbly, or falling-off knob
• Helps resolve intermittent selection when the knob doesn't grip the shaft

• Disconnect power before servicing
• Pull off the knob to access the retainer
• Align the new retainer with the shaft and press firmly until fully seated
• Reinstall the dial/knob and verify proper engagement

This screw is a direct-fit fastener used to secure appliance panels and components for stable, rattle-free operation. Replacing a stripped, missing or worn screw restores proper part alignment and prevents vibration or loose trim. What it does:

• Secures panels, trim pieces or small components to the appliance frame
• Prevents rattling or movement caused by missing or loose hardware
• Restores proper alignment for switches, panels or covers
• Works as a replacement for a single lost or damaged mounting screw

• Disconnect power and water before beginning any repair
• Use the correct screwdriver bit to avoid stripping the head
• Start threads by hand, then tighten snugly — avoid over-tightening
• Keep removed hardware in a labeled container to avoid loss

This replacement control board is made by General Electric and is compatible with dryers. The control board controls the dryer functions, such as the temperature and drying time. If this part is faulty, the dryer settings might not be able to be selected or may not work as intended. If the user notices the error code 005 showing on the display, the control board needs to be replaced.This is an authentic OEM part made of high-quality, durable materials to ensure the best possible quality. This control board can be used with dryers manufactured by General Electric, Hotpoint, RCA, and other brands. No other components are included with this part.

This 10-18 Hi/Lo hex-washer screw is a direct-use replacement fastener for appliance panels, brackets and components. It restores secure mounting and helps stop loose trim, rattling or parts that shift during use. What it does:

• Secures panels, trim pieces, mounting brackets and similar components that use a 10-18 thread with a hex-washer head
• Restores proper fit where screws are missing, stripped, or corroded
• Helps eliminate rattling, vibration noise, and misaligned parts caused by loose fasteners
• Matches OEM head and thread style for a correct mechanical fit in specified locations

• Turn power or gas to the appliance off before working on electrical or gas-equipped units; unplug when applicable
• Use the correct sized hex driver or socket to avoid rounding the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging thin sheet metal
• If replacing multiple fasteners in a load-bearing area, replace all to ensure even fit and alignment

This replacement badge is the small logo emblem that mounts to the appliance exterior to restore original appearance and branding. It provides a clean, professional look when the original emblem is missing, faded, or damaged. What it does:

• Replaces a missing, cracked, or faded exterior logo emblem
• Restores factory appearance on doors, panels, or control bezels
• Helps identify the appliance and maintain resale value
• Cosmetic-only part; does not affect appliance operation

• Surface-mount installation; may use adhesive or snap-fit depending on model—inspect original attachment method before installing
• Clean and dry mounting surface thoroughly for best adhesion
• Handle carefully to avoid scratching finished surfaces

A replacement 10-16 shoulder screw (Type A) used to secure appliance components where a shoulder/clearance is required. Restores proper alignment and fastening for panels, brackets, or assemblies that use a shoulder-style fastener. What it does:

• Provides a fixed shoulder to control depth and spacing between parts
• Secures panels, brackets, or moving parts while allowing an exact clearance
• Helps prevent over-driving and protects mating parts from damage
• Commonly used where precise alignment or rotation clearance is needed

• Inspect the mating hole and threads for damage before installing
• Use the correct driver and torque—do not over-tighten to avoid stripping
• Replace with the same screw type and size to maintain proper fit and clearance
• Disconnect power and follow all safety precautions when accessing internal components

The Ground Screw is an OEM part for GE dryers. It ensures proper grounding and electrical safety for your dryer. This screw securely connects the ground wire to the dryer chassis, providing a path for electrical current to safely discharge in the event of a fault or power surge.

A bad Ground Screw can lead to electrical issues and potential safety hazards. Causes of a bad Ground Screw can include corrosion, loose connections, or damage due to accidental mishandling or improper installation.

Symptoms of a bad Ground Screw include:

• Intermittent dryer operation
• Visible signs of damage or deterioration on the screw or ground wire
• Tripped circuit breakers or blown fuses

Replace your faulty or damaged Ground Screw with this genuine OEM GE part to ensure proper grounding and electrical safety for your dryer. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.