Parts for Ge PB930SJ1SS: Control Panel Parts

Trim and cap assembly for electric ranges. Covers and finishes edges around cooktop or control panel. Replace if cracked, chipped, discolored, or missing.

Gray plastic end plate for ranges. Covers and protects the side edge of the range body. Replace if cracked, broken, discolored, or missing for a complete look.

If your range or oven has a circuit not working or intermittent function, this electrical jumper wire bridges terminals to restore proper continuity.

Can't control your range from your phone or app? This Wi-Fi module restores smart connectivity when remote features stop working or won't connect.

This control cover is the replacement trim that protects and finishes the range/oven control console, restoring a clean appearance and shielding the underlying switches and electronics from spills and debris. It fits where the control panel sits and helps keep controls accessible and protected. What it does:

• Covers and protects the control console and underlying switches from spills, food, and dust
• Restores a finished appearance to a damaged, cracked, or missing control trim
• Helps prevent accidental contact with control buttons and electronic components

• One control cover

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Removal/installation typically requires basic hand tools (screwdriver) to unfasten screws or clips
• Handle edges carefully; plastic trim can have sharp edges when damaged

Fix an unresponsive oven touchpad or blank display with this control and overlay assembly. Restores clock, input functions, and command readability.

Burner won't adjust temperature or stuck on high? This surface burner control switch restores heat control. Quick 10-minute fix with basic tools.

Burner won't turn off or stays on when set to off? This surface burner infinite switch controls heat levels. Takes 10-15 minutes to replace.

Fix burner stuck on high or won't heat properly. This infinite switch control regulates surface element power. Direct OEM replacement, moderate DIY.

Fix burners stuck on high or won't adjust temperature with this infinite control switch. Controls dual-element burner heat settings. 30-min DIY fix.

Stainless infinite control knob for electric ranges. Replaces worn, cracked, or missing knobs on burner controls. Restores smooth heat selection.

Range indicator light signals when heating elements are active. Replace when light fails to illuminate or is damaged to restore visibility and safety.

Clear protective lens for range indicator lights. Replace when cracked, discolored, or missing to restore visibility of cooktop status lights. Verify fit with your range model number.

This wire harness connects an oven or cooktop infinite switch to the appliance's power and controls, restoring reliable burner control and electrical continuity. Designed to match the original harness routing and connectors. What it does:

• Provides the electrical connection between the infinite control switch and the appliance wiring
• Restores proper burner control when a worn or damaged harness causes loss of power to a burner
• Can stop intermittent heating, no-heat, or unresponsive burner control symptoms related to broken or shorted wiring
• Uses OEM-style connectors and lengths to align with factory switch and terminal locations

• Disconnect power before beginning any repair
• Compare the new harness to the old one for connector type and routing before installation
• Route wires to avoid pinch points and heat sources; secure with factory clips or ties
• If connector pins are corroded or damaged, replace connectors or the affected components to ensure a solid connection

This wire harness routes signals between the appliance control board and CAT module, restoring reliable electrical connections for control functions. It's a direct-fit replacement when the original harness is damaged or worn. What it does:

• Carries power and signal wires between the control board and CAT module to enable control communication
• Helps resolve intermittent or no-response control panel behavior caused by frayed, burned, or broken harness wiring
• Maintains proper connector alignment and secure electrical contacts for consistent operation
• Replaces a visibly damaged or corroded harness to prevent shorts and restore functionality

• Disconnect power before inspecting or replacing the harness to avoid shock or shorting components
• Inspect connectors and mating pins for damage; replace harness if insulation, terminals, or clips are compromised
• Route harness away from heat sources and moving parts; secure with existing clips or ties

This replacement mounting screw is used in cooking appliances to fasten components securely. It restores a tight, rattle-free fit so panels, brackets, or burner-related parts stay properly aligned during everyday use.

• Secures appliance component

This silicon controlled rectifier (SCR) is a replacement power-control semiconductor that helps regulate heating or motor circuits in compatible appliances. Restores controlled switching for stable operation and consistent performance. What it does:

• Controls power delivery to heating elements or motors by switching current on and off
• Helps correct symptoms such as intermittent heating, burners or motors that won't respond, or erratic operation
• Replaces a failed or shorted SCR to restore proper control functionality
• Operates as part of the appliance's control/regulator circuitry to manage current flow safely

• Disconnect power (unplug appliance or switch off circuit breaker) before servicing
• Observe ESD precautions and avoid touching semiconductor contacts; handle by the body or mounting tab
• Verify correct replacement orientation and secure mounting; match wiring/terminal locations exactly

Black. 8-18 AB HXW 3/8