Parts for Ge PB980SJ4SS: Control Panel Parts

Control panel trim assembly for electric ranges. Covers and secures the control panel area. Replace if cracked, broken, or discolored to restore appearance.

The control panel End Plate (Left) is an OEM part for GE electric ranges. It forms a barrier along the back left edge of the control panel area providing structural reinforcement and protection.

Over time, end plates can sustain damage due to normal wear and tear of using range buttons/dials daily as well as impacts from accidental bumps. Causes may include operation fatigue plus occasional mishandling.   

Causes of a bad end plate include:

• Dents, scratches or cracks in the protective barrier surface
• Loosened mounting fasteners holding it securely  
• Reduced control panel integrity and rigidity over long use
• Exposure of fragile internal electronics to potential damage

This exact GE replacement part also fits Hotpoint, RCA and select Kenmore models.

Right-hand end panel for electric ranges. Covers and protects the side of your range. Replace if cracked, scratched, or damaged for a clean appearance.

Front edge trim that covers the gap between your range cooktop and control panel. Replaces cracked, chipped, or missing trim for a finished look.

If your range or oven has a circuit not working or intermittent function, this electrical jumper wire bridges terminals to restore proper continuity.

This control cover is the replacement trim that protects and finishes the range/oven control console, restoring a clean appearance and shielding the underlying switches and electronics from spills and debris. It fits where the control panel sits and helps keep controls accessible and protected. What it does:

• Covers and protects the control console and underlying switches from spills, food, and dust
• Restores a finished appearance to a damaged, cracked, or missing control trim
• Helps prevent accidental contact with control buttons and electronic components

• One control cover

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Removal/installation typically requires basic hand tools (screwdriver) to unfasten screws or clips
• Handle edges carefully; plastic trim can have sharp edges when damaged

The oven control and overlay assembly are installed directly in the front of the main console of the oven. They contain the control interface of the appliance. When the overlay assembly and control interface malfunction, normally, the backlight goes out behind the console. The user is unable to see any controls or function information. This malfunction can be caused by electrical short or external damage. It's possible a fuse could be the problem, and a voltage tester can give you a clear indication of where the problem lies. Begin the installation by unplugging the oven first. Using a screwdriver, unthread the screws around the perimeter of the main user interface. This will allow the casing around the console to come off. On the rear of the oven, remove the screws holding the back panel in place until the control board can be seen. Unscrew the control board assembly from the control overlay assembly. Repeat these steps in reverse with the new part.This GE oven control and overlay assembly is a genuine OEM product sourced directly from the manufacturer. The listed product is sold individually. This part is compatible with GE, Kenmore, HotPoint, RCA, and Kenmore.

Fix burners stuck on high or won't adjust temperature with this infinite control switch. Controls dual-element burner heat settings. 30-min DIY fix.

Burner won't adjust temperature or stuck on high? This surface burner control switch restores heat control. Quick 10-minute fix with basic tools.

Fixes range not heating or oven functions not working. This rotary switch controls bake, broil, and keep warm settings from the control panel.

Burner won't turn off or stays on when set to off? This surface burner infinite switch controls heat levels. Takes 10-15 minutes to replace.

Stainless infinite control knob for electric ranges. Replaces worn, cracked, or missing knobs on burner controls. Restores smooth heat selection.

Range indicator light signals when heating elements are active. Replace when light fails to illuminate or is damaged to restore visibility and safety.

Clear protective lens for range indicator lights. Replace when cracked, discolored, or missing to restore visibility of cooktop status lights. Verify fit with your range model number.

This replacement mounting screw is used in cooking appliances to fasten components securely. It restores a tight, rattle-free fit so panels, brackets, or burner-related parts stay properly aligned during everyday use.

• Secures appliance components to the chassis or assembly
• Replaces a missing, stripped, or corroded screw
• Helps resolve loose panels, wobbling parts, or vibration noises
• Supports proper alignment of mounted parts

• Disconnect power at the breaker; for gas units, also shut off gas supply
• Allow the appliance to cool completely before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Tighten snugly without overtightening; replace damaged threads or hardware as needed

Black. 8-18 AB HXW 3/8

Lubricant cleaner for range and oven control shafts, burner valves, and rack paddles. Dissolves residue and restores smooth operation when parts feel stiff.