Parts for Ge PS950EF3ES: Control Panel Parts

This control trim and gasket assembly replaces the exterior trim and sealing gasket around the oven/range control panel to restore fit, finish, and a proper seal. It helps keep heat, grease and moisture away from the control area for reliable performance. What it does:

• Covers and secures the control panel edge for a finished appearance
• Provides a gasket seal to limit heat and moisture intrusion behind the control housing
• Helps reduce vibration or rattling by holding the trim tight to the cabinet
• Prevents grease and grime from collecting behind the control area, simplifying cleaning

• 1 control trim and gasket assembly

• Disconnect power to the appliance before starting any work
• Remove control panel fasteners or clips to access the trim; keep all screws for reassembly
• Handle trim and underlying components carefully to avoid scratching or bending

This electrical jumper links two terminals within the appliance's wiring to restore proper continuity for the affected circuit. Replace a burnt, damaged, or missing jumper to bring the related function back to reliable operation.

• Bridges terminals to complete or modify an electrical circuit as designed by the manufacturer
• Helps address symptoms like a specific feature not working, intermittent operation, or no power to a component
• Replace if the original shows heat damage, broken leads, or loose connections
• Direct replacement for the original jumper used in the wiring harness

• Disconnect power at the breaker or unplug the appliance before servicing
• Use your model's wiring diagram to locate the correct jumper
• Label/photograph wire positions and transfer one connection at a time
• Ensure connectors are fully seated; do not alter the factory wiring configuration

The GE Control UI Assembly is an OEM part for GE ranges. It features interface buttons and indicators for the oven.

Symptoms of a bad control UI include:

• Non-responsive or sticky buttons  
• LED lights that no longer illuminate cooking modes
• Faded or scratched graphics that cannot be read

Causes may involve years of repeated exposure to heat, moisture, and cleaning chemicals breaking down the overlay surface. Accidental damage could also crack delicate interface components. 

This OEM GE part is also compatible with Hotpoint, RCA, and select Kenmore models.

This guide & overlay assembly replaces the worn or damaged trim piece that guides and covers the appliance control area, restoring a clean, secure panel appearance and proper button/knob alignment. What it does:

• Provides the outer trim/guide for the control panel so buttons and knobs seat correctly
• Protects underlying switches and electronics from spills and debris
• Restores alignment and prevents sticking or misaligned controls caused by a damaged guide
• Improves the appliance's appearance by replacing faded, cracked, or peeled overlays

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle the overlay carefully to avoid scratching or bending during installation
• Installation typically requires removing the control panel or bezel; follow the OEM service instructions
• Use appropriate tools and keep track of screws and clips

This glass control and board assembly replaces the cooktop's front touch/control panel and the electronic board behind it, restoring user input and control of heating functions. Fits single-surface electric/induction ranges using a glass control assembly. What it does:

• Replaces the glass touch/control panel and the associated control electronics that register user commands.
• Restores responsive touch keys/buttons and display functions when worn or unresponsive.
• Resolves symptoms such as unresponsive controls, missing display LEDs, intermittent control behavior, or failure to start heating cycles.
• Interfaces with range power and element control circuits to send user commands to the cooktop.

• One glass control panel with attached control board assembly.

• Disconnect power at the breaker before starting; serious shock hazard if power is not removed.
• Handle the glass panel carefully to avoid cracking; use proper lifting and support during removal/installation.
• Note connector locations and mounting hardware; mark or photograph wiring before disconnecting.

This filter clock display is the replacement display assembly that shows the refrigerator clock and filter status indicators, helping you know when a water filter needs changing and restoring normal display function. What it does:

• Shows the refrigerator clock and elapsed time indicator for the water filter
• Displays filter status prompts so you can tell when a replacement is due
• Restores a blank, faded, or unresponsive filter/clock display
• Helps reset or update the filter life indicator when paired with proper reset steps

• Disconnect power to the appliance before beginning any work to avoid shock or injury.
• Handle the display assembly carefully to avoid scratching or damaging the lens or contacts.
• Small tools may be required to remove the control panel; keep track of screws and retainers.
• Follow model-specific disassembly and reassembly instructions.

Replacement screw that secures panels, trim and internal brackets to keep appliance components stable and rattle-free. Use when originals are missing, stripped, or broken to restore proper fit and safe operation. What it does:

• Secures panels, control housings, trim and small brackets so parts stay aligned and stable.
• Replaces missing or damaged fasteners that cause rattling, vibration, or loose assemblies.
• Keeps electrical and mechanical components properly positioned for reliable operation.
• Intended as a direct replacement where the OEM screw specified for the application is required.

• Disconnect power and unplug the appliance before starting any repair.
• Use the correct screwdriver or bit and seat the screw squarely to avoid stripping the head or threads.
• Do not overtighten—stop when snug to prevent damage to panels or plastic components.
• Keep removed screws organized; replace only with the identical OEM screw for proper fit.

Nickel