Parts for Ge ZGP366NR4SS: Control Panel Parts

This wiring harness provides the factory-style electrical connections between the appliance control and its components, restoring reliable signal and power routing for proper operation. What it does:

• Routes power and control signals between the main control and connected components
• Replaces damaged, frayed, or corroded wiring that can cause intermittent operation
• Helps stop symptoms like components not powering on, intermittent cycles, or blown fuses
• Restores secure connector mating to reduce arcing and poor contacts

• One factory-style wiring harness with attached connectors as shown

• Disconnect all power (unplug or shut off breaker) before starting work
• Compare the part to the original to confirm connector types and wire lengths before installing
• Route and secure the harness following the appliance's wiring channels; avoid contact with sharp edges or moving parts

Size: 8 - 32 inch.

This glass display is the replacement front glass for the appliance control panel. It restores a clean, readable surface for the controls and protects the underlying electronics from spills and debris. What it does:

• Replaces cracked, scratched, or chipped control panel glass to improve appearance and readability
• Protects the control board and touch/button assembly from spills, grease, and light impact
• Helps maintain proper user interaction with the oven/range controls when the original glass is damaged
• Matches the OEM shape and mounting points for a like-for-like fit when installed

• Disconnect power (unplug or shut off circuit breaker) before starting any work
• Remove control console trim and any fasteners carefully to avoid chipping the glass
• Handle glass edges with caution; wear cut-resistant gloves and eye protection

This control bracket secures the appliance control assembly to the cabinet, helping keep buttons, knobs, and the control board properly aligned for reliable operation. Designed to restore stable control-panel mounting after damage or wear. What it does

• Holds the control/module assembly in the correct position so front controls operate smoothly
• Prevents excessive movement or vibration that can cause intermittent button or knob issues
• Restores proper alignment after a broken or bent mounting tab
• Helps maintain electrical connections by stabilizing the control module

• Designed to replace a broken or bent bracket; inspect surrounding clips and fasteners for damage before installing
• Power off and unplug the appliance before attempting removal or installation to avoid shock
• Typical installation requires removing the control panel or console—retain screws and grounding hardware
• Handle the board carefully to avoid static discharge or connector damage

This LED board is the refrigerator interior light assembly that restores bright, even illumination inside the fresh-food compartment for easier visibility and safer food access. What it does

• Powers and distributes LED light to illuminate the refrigerator interior
• Replaces a failed or dimming light board to stop flicker or complete loss of interior lighting
• Ensures even light coverage across the compartment for better visibility
• Works with the refrigerator's existing light housing and connectors to restore normal operation

• One LED board

• Disconnect power to the appliance before starting any work
• Handle the board by its edges and avoid touching LED components or circuitry
• Remove shelves and trim as needed to access the light housing; keep track of screws and retainers
• Reconnect all wiring and verify proper operation before reassembling the compartment

The Encoder Assembly is an OEM part for GE gas ranges. It digitally converts analog knob movements into signals to control the gas valve, igniter, and temperature settings. 

Causes of a bad encoder assembly include degradation of internal sensors and switches over time, loose wiring connections, or impacts that cause misalignment.

Symptoms of a bad encoder assembly are:

• Delays or errors when trying to light burners
• Inaccurate flame height and temperature level responses 
• Knobs feel sticky, sluggish or jump between settings
• Error codes indicating control module communication issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models.

The Control Display Module is an OEM part for GE gas ranges. It is the central component responsible for controlling and monitoring all functions and settings of the range through an LCD interface. 

Symptoms of a bad control display module include: 

• Blank or unresponsive control display  
• Inability to set or change oven temperatures
• Fault codes or error messages appearing 
• Control keys sticking or not responding properly

Causes of a bad control display module can include circuit board failure, liquid damage, overheating issues, or normal component degradation over time.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This control knob lets you select burner or oven settings on your range or cooktop. It fits onto the control shaft; replacing a cracked or stripped knob restores a secure grip and accurate setting selection. What it does:

• Attaches to the valve/switch shaft to turn the surface burner or oven control
• Provides a clear pointer and comfortable grip for setting selection
• Common symptoms: cracked housing, stripped insert, loose/wobbly knob, or the knob falls off

• One control knob assembly

• Disconnect power and let the appliance cool; shut off gas if required by your model's manual
• Pull the old knob straight off the shaft—do not pry or twist the shaft
• Align the flat/keyed side of the new knob with the shaft and press straight on until fully seated
• Verify pointer alignment and smooth operation through all settings

Replacement knob assembly for the grill/broil thermostat — restores reliable temperature control and a secure grip. Easy to swap, it gets your grill control working smoothly so you can set heat levels with confidence. What it does:

• Restores positive engagement for the grill/broil thermostat when the original knob is cracked, missing, loose, or spins freely
• Allows accurate selection of grill temperature settings and repeatable control feel
• Direct-fit control knob designed to match the OEM spline and dial orientation for proper operation
• Durable construction made for regular oven use

• Disconnect power or unplug the appliance before beginning any repair
• Remove the old knob by pulling it straight off the control shaft; align the new knob with the control spline and push until fully seated
• No special tools typically required; if the knob is stuck, use gentle leverage and avoid metal prying that could damage the shaft
• Allow the appliance to cool before working near heating elements or hot surfaces

This lens bezel covers and protects the appliance's front control panel, keeping buttons and displays visible while shielding them from spills and wear. It restores the appearance and function of the control area for a clean, readable interface. What it does:

• Protects the control panel lens and underlying electronics from splashes, spills, and everyday wear
• Provides a clear viewing surface for display readouts and button labels
• Helps keep button/dial areas aligned and prevents debris from entering gaps
• Restores a worn, cracked, or scratched control area to improve usability and appearance

• One lens bezel

• Remove power to the appliance before beginning any work to avoid shock or injury
• Typically secures with clips or screws; handle the lens gently to avoid cracking
• Inspect surrounding trim and gaskets during reassembly; replace damaged fasteners as needed

A replacement front bezel assembly that restores the oven's front trim and helps keep the door area properly aligned and sealed. Replaces a damaged or worn front trim to renew appearance and fit. What it does

• Provides the front-facing trim around the oven opening and door area.
• Secures and aligns the oven door and related trim pieces for proper closure.
• Replaces cracked, warped or cosmetically damaged bezel pieces.
• Helps stop drafts and visible gaps caused by a broken or bent front trim.

• One oven bezel assembly (front trim), as shown.

• Disconnect power to the range before starting any service to avoid shock or injury.
• Installation typically requires removing the oven door or outer door components and unscrewing retaining fasteners; keep track of screws and clips.
• Handle with care to avoid scratching the finish; verify orientation before final fastening.

This is a stainless-steel machine screw used to secure components in appliances. Its #8-18 thread and 3/8" length provide a reliable, corrosion-resistant fastening where a short machine screw is required. What it does:

• Fastens panels, brackets, or small assemblies with a #8-18 threaded hole
• Resists rust and corrosion in humid appliance compartments
• Provides a short, secure hold where space is limited
• Compatible with standard #2 Phillips or compatible driver bit for installation

• Power off and unplug the appliance before servicing
• Use the correct driver to avoid stripping the head
• Do not overtighten; stop when snug to avoid thread or component damage
• If replacing multiple fasteners, reuse only the same size and type