Parts for Ge ZGP366NT1SS: Control Panel Parts

This stainless steel control panel trim restores the finished look around your appliance's control area and helps protect the controls from spills, splashes, and everyday wear. It matches OEM fit and finish for a clean, factory appearance. What it does:

• Replaces a scratched, dented or bent control panel bezel to improve appearance
• Protects the control cluster from spills and light impact
• Keeps buttons and display edges properly framed to maintain normal operation
• Fits around the control area to restore proper alignment and sealing

• Disconnect the appliance from power (and gas, if applicable) before starting any repair
• Basic hand tools are typically required; access usually gained by removing the control panel or outer cabinet trim
• Handle the bezel carefully to avoid scratching the finish during install
• If mounting hardware or clips are damaged, replace them with OEM parts for a secure fit

This is a stainless-steel machine screw used to secure components in appliances. Its #8-18 thread and 3/8" length provide a reliable, corrosion-resistant fastening where a short machine screw is required. What it does:

• Fastens panels, brackets, or small assemblies with a #8-18 threaded hole
• Resists rust and corrosion in humid appliance compartments
• Provides a short, secure hold where space is limited
• Compatible with standard #2 Phillips or compatible driver bit for installation

• Power off and unplug the appliance before servicing
• Use the correct driver to avoid stripping the head
• Do not overtighten; stop when snug to avoid thread or component damage
• If replacing multiple fasteners, reuse only the same size and type

This wiring harness provides the factory-style electrical connections between the appliance control and its components, restoring reliable signal and power routing for proper operation. What it does:

• Routes power and control signals between the main control and connected components
• Replaces damaged, frayed, or corroded wiring that can cause intermittent operation
• Helps stop symptoms like components not powering on, intermittent cycles, or blown fuses
• Restores secure connector mating to reduce arcing and poor contacts

• One factory-style wiring harness with attached connectors as shown

• Disconnect all power (unplug or shut off breaker) before starting work
• Compare the part to the original to confirm connector types and wire lengths before installing
• Route and secure the harness following the appliance's wiring channels; avoid contact with sharp edges or moving parts

This bezel control knob replaces a worn or broken range/stove control knob so you can turn stove functions accurately and safely. It restores tactile grip and clear pointer alignment for reliable temperature or burner selection. What it does:

• Fits on the control shaft to select burner, oven or cooktop settings.
• Restores a secure grip and clear pointer position when the original knob is cracked, loose, or missing.
• Helps prevent accidental setting changes by providing a firm, indexed control.
• Compatible with standard control shafts where a bezel-style knob was originally used.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Pull the old knob straight off the shaft; align the new knob's spline with the shaft and push on until seated.
• If the knob does not seat easily, inspect the shaft for damage.
• If underlying switch or shaft is damaged, replace the damaged component.

The GEA3 Wi-Fi communication board provides the refrigerator's wireless interface so the appliance can connect to your home network and the manufacturer's mobile services. Restores smart features like remote monitoring and alerts when the original board fails. What it does

• Enables the refrigerator to join a home Wi-Fi network for app connectivity and smart features
• Handles wireless communication between the appliance and cloud services
• Works with the appliance's main control system to send/receive settings and notifications

• One GEA3 Wi-Fi communication board (single wireless interface module)

• Disconnect power to the appliance before replacing the board to avoid shock or damage
• Handle the board as an electrostatic-sensitive device; avoid touching contacts and use ESD precautions if possible
• Reinstall per the appliance wiring diagram/service manual and secure all connectors firmly
• After installation, power the appliance and follow the manufacturer's pairing or network setup steps (may require app re-registration)

This housing transceiver is the outer mounting enclosure that secures and protects the appliance's transceiver assembly, helping maintain reliable signal and control communication. It replaces cracked or broken housings to restore proper fit and protection. What it does:

• Holds and protects the wireless/transceiver module and related wiring from physical damage
• Helps maintain proper alignment and connection to the appliance control assembly
• Common symptom: damaged or cracked housing that exposes electronics or prevents secure mounting
• Common symptom: intermittent signal or communication issues when the transceiver is loose or misaligned

• One housing transceiver

• Disconnect power to the appliance before beginning any repair to avoid shock or component damage
• Handle the transceiver and circuit connections carefully to avoid bending pins or ESD damage
• Installation typically requires removing the control console or access panel and a few fasteners; keep track of screws and gaskets